Regency Horizon HZ30E-LP1 Owners & Installation Manual Download Page 13

Page: 13 / 64

Regency Horizon™ HZ30E-1 Gas Fireplace

INSTALLATION

WALL MOUNT ON / OFF SWITCH AND RECEIVER INSTALLATION

REQUIRED FOR ALL INSTALLATIONS - INCLUDING PROFLAME REMOTE CONTROLS

* Installation of the Receiver must be completed before installing facing materials.

J-Box

Receiver

Wall Plate

Slider Switch

Low Voltage Junction Box

12 pin connector - located

on outer right side of the

fi rebox.

MPORTANT INSTALLATION NOTE:

The Receiver must be placed inside the supplied (Low Voltage)

junction type wall box and installed into the wall only.

DO NOT INSTALL WITHIN THE CONFINES OF THE FIREPLACE.

Wall Mounting

1. Install the junction box to the framing, at desired location within 10 ft. from fi replace.

2. Feed the 12 pin connector through the opening at back of junction box.

3. Connect the 12 pin connector to the back of the receiver.

4. Install the Receiver in the Low Voltage Junction box, supplied with HZ30E.

5. Insert the 4 AA type batteries in the battery compartment with the correct polarity.

6. Place the slider into the cover plate.

7. Put the Receiver switch in the “OFF” position, to allow correct lineup for slider switch.

8. Make sure the Receiver and cover plate words “ON” and “UP” are on the same side.

9. Align the slider with the switch on the Receiver and couple the switch into the slider.

10. Align the screw holes.

11. Using the two (2) screws provided secure the cover plate to the Receiver.

GT REMOTE INSTALLATION

1. GT remote installation - see

Profl ame remote instructions for coding remote to receiver as well as operat-

ing instructions.

Summary of Contents for Horizon HZ30E-LP1

































































Search results

Summary of Contents for Horizon HZ30E-LP1

Reviews:

Related manuals for Horizon HZ30E-LP1

Brands by name

Popular brands

Regency Horizon HZ30E-LP1, Owners & Installation Manual

Search results

Summary of Contents for Horizon HZ30E-LP1

Reviews:

Related manuals for Horizon HZ30E-LP1

Brands by name

Popular brands