Regency Hampton HI2450 Owners & Installation Manual Download Page 12

Page: 12 / 48

Regency HI2450M

installation

Standard Cast Faceplate
Installation

12/23/10

918-300g

HI300

CAST FACEPLATE

INSTALLATION

Page 1 of 3

Secure the Side Mounting Brackets (packaged with Faceplate)

to the left and right side of the fi rebox using 4 bolts per mounting

bracket as shown in the diagram below.

Side

Mounting

Bracket

Backside of Unit Shown.

Backside of Unit & Faceplate Shown.

Secure the Left and Right Side Faceplate to the fi rebox by align-

ing the Mounting Holes with the Side Mounting Brackets taking

care to align vertically while each side rests on the hearth. Secure

using 1 bolt per bracket.

Side Mounting

Bracket

Mounting

Hole

Right Side

Faceplate

Left Side

Faceplate

Place Mantel Top onto the top of the fi rebox.

Mantel Top

Right Side

Cast

With the Mantel Top in place check to make sure there is no gap

between the nut retainer and the underside cast of the Mantel

Top. If there is a gap present you will need to lower that side cast

by loosening 2 bolts, see step 6 for bolt location (check to see if
level).

FACEPLATE CONTENTS LIST

Qty

Description

Left Side Faceplate

Right Side Faceplate

Top Faceplate

Side Mounting Brackets

1/4" - 20 x 1/2" Hex Head Bolts

1/4" Lock Washers

1/4" Flat Washers

47" Insulations

Summary of Contents for Hampton HI2450

















































Search results

Summary of Contents for Hampton HI2450

Reviews:

Related manuals for Hampton HI2450

Brands by name

Popular brands

Regency Hampton HI2450, Owners & Installation Manual

Search results

Summary of Contents for Hampton HI2450

Reviews:

Related manuals for Hampton HI2450

Brands by name

Popular brands