Regency GF900L-LPG1 Page 4 Owners & Installation Manual Download

Page: 4 / 52

Regency GF900L-1 Gas Fireplace

SAFETY LABEL

safety decal

This is a copy of the data badge that accompanies each GF900 Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.

NOTE: Regency

units are constantly being improved. Check the badge on the unit and if there is a difference, the badge on the unit is the correct one.

COPY OF DATA BADGE

Rev. A

Part #: 919-117

Colour: Black on Grey

Size: 100% 7" W x 2.7" H

Mar.22/12 - draft for approval.

May 30/12 - Made changes as per test report.

June 25/12 - Added AGA Approval

Dec. 23/13: Updated E. Aus address

Serial

Number

Regency Gas Fireplace

405

Distributed by:

To be installed by an authorised person in

accordance with installation instructions

provided with the appliance.

Western Australia:

Air Group Australia

28 Division St

Welshpool, WA 6106

Eastern Australia

Fireplace Products

Australia Pty. Ltd.

1 Conquest Way

Hallam, VIC 3803

Electrical: 240V 50 Hz

919-117a

Gas Type

NG LPG ULPG

Model

GF900L-NG GF900L-LPG GF900L-ULPG

Gas Consumption

35 mj. 28 mj. 28 mj.

Manifold Pressure

0.87 kPa 2.49kPa 2.49 kPa

Injector Size

1 x #35 1 x#53 1 x #53

2.80mm 1.50mm 1.50mm

Model

Approval No.

AGA 7908 G

Code AS4553 / NZS5262 / NZS5266

DO NOT

OPERATE THIS APPLIANCE BEFORE READING THE
INSTRUCTIONS BOOKLET.
PLACE ARTICLES ON OR AGAINST THIS APPLIANCE
STORE CHEMICALS OR FLAMMABLE MATERIALS

SPRAY AEROSOLS IN THE VICINITY OF THIS

APPLIANCE WHILE IN OPERATION.

OPERATE WITH PANELS, COVERS OR GUARDS
REMOVED FROM THIS APPLIANCE.
ENCLOSE THIS APPLIANCE.
DO NOT MODIFY THIS APPLIANCE.

NEAR THIS APPLIANCE.

DO NOT

908-602a

(Australia Only)

Summary of Contents for GF900L-LPG1





















































Search results

Summary of Contents for GF900L-LPG1

Reviews:

Related manuals for GF900L-LPG1

Brands by name

Popular brands

Regency GF900L-LPG1, Owners & Installation Manual

Search results

Summary of Contents for GF900L-LPG1

Reviews:

Related manuals for GF900L-LPG1

Brands by name

Popular brands