Regency Fireplace Products Energy U31 Owners & Installation Manual Download Page 28

Page: 28 / 48

28 | Regency U31-10 Gas Fireplace Insert

installation

Diagram 4

Diagram 5

Rear View: Trim Assembly

Diagram 2

Diagram 3

Rear View: Faceplate Assembly

Diagram 1

STANDARD FACEPLATE &

HEARTH TRIM INSTALL

Lay the faceplate panels flat, face down on

something soft so they don't scratch.

Take the top faceplate and align the holes in

it with the holes in the side panels. Using the

screws provided, attach from the top of the panel

(the holes in the top panel are slightly larger

than the holes in the side panel to facilitate

easier installation). Diagram 1.

Hint: Do not tighten the screws down completely

at this point, continue on with steps 3 and 4

and do a trial fit to the unit. Make any neces

sary adjustments and when it fits properly then

tighten down the screws.

Hearth Trim Option:

Hearth Trim is an option

that can be used to finish off the installation

when the bottom of the fireplace is higher than

the hearth or to raise the fireplace. Attach the

Hearth Trim to the bottom of the faceplate side

panels with the screws provided. See Diagram

Using the connectors provided, join the left side

trim (with the ON/OFF switch) to the top trim.

Diagram 2. Connect the right side trim to the

top trim.

Place the trim on the assembled faceplate panels,

aligning the wire connections from the switches

with the notch on the left side panel.

Connect the fan switch wires by taking the

black and red wires with the male ends (in

the grey harness) and connect them with

the wire connectors from the fan speed

control.

Tuck the wires into the faceplate to keep

them away from the insert using the clip

provided. Attach the clip to the rear of the

faceplate to ensure that the wires do not

touch the side of the unit. Diagram 3.

The power cord should be run behind the

faceplate panel.

Attach the brass trim to the faceplate by

drilling a 1/8" hole through into the faceplate

using the hole in the trim as a guide. Fasten

the trim to the faceplate panels using the

plated screws. Diagram 4.

Attach the faceplate panels to the insert

body using the 4 remaining black screws.

Diagram 5.

10.

Push the Regency logo plate into the two

holes in the bottom left corner of the face-

plate.

Summary of Contents for Energy U31

















































Search results

Summary of Contents for Energy U31

Reviews:

Related manuals for Energy U31

Brands by name

Popular brands

Regency Fireplace Products Energy U31, Owners & Installation Manual

Search results

Summary of Contents for Energy U31

Reviews:

Related manuals for Energy U31

Brands by name

Popular brands