Regency Fireplace Products E18E-LP11 Owners & Installation Manual Download Page 23

Page: 23 / 104

Regency

E18E-11 Gas Fireplace Insert

| 23

installation

REQUIRED STEPS AND PROCEDURES FOR E18E INSTALLATION

1. Locate model on existing ZC box - locate corresponding section in this manual.

2. Make necessary alteration to the ZC firebox as per manual.

3. Separate inner and outer fire box (see procedure in manual).

4. Remove flue adaptor for outer firebox.

5. Make necessary adjustment to flue adapter mounting plate as per manual.

6. Cut flex to required length and secure to top plate using 3 screws and washers.

7. Secure top plate flue adapter to ZC box.

8. Secure flue adapter to flex using 3 screws/washers.

9. Slide outer firebox into place, be sure flue adapter mounting screw doesn't hold unit up on installation.

10. Adjust left and right side legs on outer shell (depends on ZC box it is being intalled in) - See details in manual.

11. Measure and align outer firebox as per manual, secure each corner using self tapping screws.

12. Install inner firebox into outer firebox, ensure draft hood bottom fits on top of draft hood slides, left side, right side and rear.

13. Secure inner firebox - 2 screws on top left and right side - using existing holes.

14. Secure inner firebox on bottom inside - 2 screws on each side. Be sure to re install panel brackets, and line up with existing holes.

15. Reinstall burner.

16. Make gas connection - check for leaks.

17. Install enamel panels.

18. Install Faceplate

19. Install Glass Crystals on burner.

20. Light pilot.

21. Install glass door.

22. Install thermostat.

•  Nibbler
•  Oscillating tool / metal blades
•  Tin snips
•  Uni Bit/Step Drill
•  Black high temp paint
•  Drill/ ¼” bit – Phillips bit
•  Measuring tape
•  Level
•  Sharpie
•  Shop vacuum

TOOLS REQUIRED (SUGGESTED)

Nibbler

Oscillating tool

Optional:

•  Plasma cutter
•  Fibre drop sheet
•  Fire extinguisher

f i r e - p a r t s . c o m

Summary of Contents for E18E-LP11









































































































Search results

Summary of Contents for E18E-LP11

Reviews:

Related manuals for E18E-LP11

Brands by name

Popular brands

Regency Fireplace Products E18E-LP11, Owners & Installation Manual

Search results

Summary of Contents for E18E-LP11

Reviews:

Related manuals for E18E-LP11

Brands by name

Popular brands