background image

20

     | 

ACV40E City Series

installation

Caution Requirements

The top, back and sides of the fireplace are defined by 

standoffs. The metal ends of the standoff may 

NOT

 be 

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk 

if these clearances (air space) to combustible materials are not 

adhered to. It is of greatest importance that this fireplace and vent 

system be installed only in accordance with these instructions.

Clearances

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this 
fireplace and vent system be installed only in accordance with these instructions.

Clearance: single sided

Dimension

Measured From:

A: Mantel Height (min.)

**

Top of Fireplace Opening

B1: From Floor

Min. 0mm

Bottom of Fireplace Opening

B2: Opening Height

383mm

Bottom/Top of Fireplace Opening

C: Sidewall (on one side)

216mm

Side of Fireplace Opening

D: Mantel Depth (max.)

**

E: Alcove Width

2134mm

Sidewall to Sidewall (Minimum)

 F: Alcove Depth

914mm

Front to Unit (Maximum)

G: Ceiling
    (in front of fireplace)

953mm

Top of Fireplace Opening

H: Convection Air Outlet

*

Top of Enclosure

J: Convection Air Outlet Opening Offset

0-76mm

Max. offset from top of chase enclosure

K: Chase Enclosure (Min.)

1600mm

From base of unit/floor

L: Clearance to Sprinkler Head (Min.)

914mm 

Perpendicular from chase grill 

Hearth

0"

No hearth required

** See mantel clearances chart in this manual.

Flue Clearances to Combustibles

Horizontal - Top

76mm

Horizontal - Side 

51mm

Horizontal - Bottom

51mm

Vertical

51mm

Passing  through  wall/
floor/ceiling  -  when 
firestop is used.

38mm

Alcove

E

F

D

A

C

B

1

G

B

2

J

H

K

The 

HeatWave

 Duct Kit has differ-

ent clearance and framing require-
ments, check the 

HeatWave

 manual 

for details.

ACV40E- Single sided

*

A minimum of 306 square 

centimetres of open area, 
not lower than 152mm 
from top of enclosure, 
required for all installations 

L

Chase grill

Sprinkler

Side view

Summary of Contents for City New York View 40 Series















Reviews: