background image

REDLAKE MASD, INC. 

4.5 Control Inputs 

 
The control input EXPOSE is provided as a means of externally controlling the exposure of the 
camera. This input is designed to accept RS-422 differential or, for backwards compatibility, 
single ended TTL.  To drive this input differentially connect both the (+) and (-) inputs to an  
RS-422 driver.  When the (+) input is more positive than the (-) input the camera is exposing.  
When the (+) input is more negative than the (-) input the camera performs a frame transfer and 
then idles.   
 
To drive the EXPOSE input with a single ended TTL signal source, connect one input to a TTL 
driver and leave the other input floating.  If the (+) input (pin 30) is driven then a TTL high will start 
an exposure or if the (-) input (pin 64) is driven then a TTL low will start an exposure. 
 

4.6  Mode Control Lines 

 
The operating mode of the camera is set by the MDE command.  Issuing an MDE PI command 
will delegate mode control to the MC0-MC2 mode control lines.  MC0, MC1, and MC2 provide 
backward compatibility with earlier 

Mega

Plus Camera control signals.  Each of these inputs is 

designed to accept TTL level signals referenced to ground at the connector.  MC0 and MC1 set 
the operating mode and MC2 enables the shutter.  The truth table for the control lines is as 
follows: 

 

Table 4-1. Mode Control Lines 

MC2 (Pin 33) 
TTL Input 

MC1 (Pin 32) 
TTL Input 

MC0 (Pin 31) 
TTL Input 

Shutter 
Operation 

Operating 
Mode 

Low (0 volts) 

Low (0 volts) 

Low (0 volts) 

Enabled 

Controlled 

Low (0 volts) 

Low (0 volts) 

High (+5 volts) 

Enabled 

Triggered 

Low (0 volts) 

High (+5 volts) 

Low (0 volts) 

Enabled 

Continuous 

Low (0 volts) 

High (+5 volts) 

High (+5 volts) 

Enabled 

Continuous 

High (+5 volts)  Low (0 volts) 

Low (0 volts) 

Off, blades open 

Controlled 

High (+5 volts)  Low (0 volts) 

High (+5 volts) 

Off, blades open 

Triggered 

High (+5 volts)  High (+5 volts) 

Low (0 volts) 

Off, blades open 

Continuous 

High (+5 volts)  High (+5 volts) 

High (+5 volts) 

Off, blades open 

Continuous 

 

NOTE

:  Redlake, MASD, Inc. does not recommend using MC0 through MC2 for mode control in 

new designs for 

Mega

Plus cameras.  The serial data port, with its complete command 

set, provides a more useful control interface. 

 
 
 
 
 
 
 
 
 
 
 

 

91000050-002 Revision A 

4-2 

10/01/01 

Summary of Contents for 1.4i







































Reviews: