background image

 

2

FOREWORD 

 
Congratulations on your Verti-Top purchase! For safe and long-lasting operation of this Verti-
Top, it is necessary to read and to understand this user manual.

 

It is impossible to work safely with this machine 

without

 complete knowledge of the content of 

the user manual. 
 
The Verti-Top is not a machine that works independently. It is the user’s responsibility to use 
the correct tractor. The user must also check the tractor/Verti-Top combination on safety 
aspects such as noise level, user instructions and risk analysis.

 

 
The following pages deal initially with the general safety instructions. Every user should know 
these safety instructions and apply them. At the end of this page, a registration card is 
inserted. This registration card should be returned to enable us to deal with potential future 
claims 

 

 
This user manual lists many instructions that are numbered in sequence. You should follow 

this sequence. A 

 is an indication of a safety instruction. 

 means a tip and/or 

note. 

 
All information and technical specifications provided at the moment that this document is 
published are the most recent ones. Design specifications may be changed without prior 
notice. 

 

 
This document is a translation of the original operating instructions. 
Upon request, the original operating instructions are available in Dutch. 
 
 

WARRANTY CONDITIONS 

 

WITH DELIVERY THIS VERTI-TOP IS GUARANTEED AGAINST MATERIAL DEFECTS. 
THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE DATE. 
VERTI-TOP WARRANTIES ARE SUBJECT TO THE ‘GENERAL CONDITIONS FOR SUPPLY OF 
PLANT AND MACHINERY FOR EXPORT, NUMBER 188’ THAT ARE PUBLISHED UNDER THE 
AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE. 

 

REGISTRATION CARD 

 
For your own information, fill in the table below: 

 
 
Serial number of the 
machine 

 

 
Dealer name 

 

 
Date of purchase 

 

 
Remarks 
 

 

 

Summary of Contents for Verti-Top 1200

























Reviews: