manualshive.com logo in svg

Red Star RC Yak-3, Instruction Manual, Page: 29 / 33

Share
Download
Red Star RC Yak-3 Instruction Manual Download Page 29

© 2004 Red Star RC

 

 

29

 
 

 

Glue 3/32” leftover balsa to the landing gear covers 
LG. Cover them according to the color scheme you 
choose. Mount them on the landing gear with Du-
Bro Nylon Large Straps 5/32"(not included). 
 

 

PRE-FLIGHT CHECKOUT

  

 

•

 

Make sure the servos are securely mounted 
and that the servo arms have their retaining 
screws in place.  

•

 

It is also a good idea to re-check all the 
push-rod connectors, fuel tank mounting, 
fuel lines, wheels; engine mounting, prop 
and spinner.  

•

 

Range check the radio as per the manu-
facturer’s  instructions  and  make  sure  it  is 
fully charged.  

 

DOUBLE CHECK EVERYTHING  
YOU CAN THINK OF!

   

 
A model and radio that is not prepared and working 
properly on the ground before take off will not 
improve in the air IT WILL GET WORSE! There is 
no point in attempting to fly until everything is 
100% correct.  

 

 

 
Please let us know what do you 
think about this kit and what we 
could do to make it better! 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

308 Belltown Road, Owings Mills, MD 21117-3239 

www.redstarrc.com 

[email protected] 

 
 
 
 

Summary of Contents for Yak-3


































Reviews:

No comments