RED ROOSTER TCS-500-AT2S User Manual Download Page 42

Page: 42 / 72

USER MANUAL

▪

Red Rooster Lifting Limited

▪

Nauta House, The Meadows, Oldmeldrum, Aberdeenshire, AB51 0EZ

▪

Tel: +44 (0) 1651 872101

▪

M01-AH12-AT REV1

Red Rooster Lifting Limited

Nauta House, The Meadows, Oldmeldrum, Inverurie, Aberdeenshire, UK, AB51 0EZ

T: +44 (0) 1651 872101

[email protected]

REDROOSTERLIFTING.COM

TCS-500-AT2S

AIR HOIST & TROLLEY

C06-AH12-AT REV2

STANDARD FEATURES

•

Toku rotary vane motor

•

Robust epicycle gearbox

•

Failsafe automatic internal disc brake

•

Choice of pendant controls or control stations

•

Upper & lower limit switches

•

Lightweight aluminium housing

•

Internal silencing down to 83 dB(A)

•

Alloy safety swivel hooks with safety catch

•

Load chain of European manufacture to EN818-7

•

Trolley to suit various flange profiles

•

Anti-tilt & anti-drop plates

•

High efficiency motor gearbox

•

Heavy duty sealed wheel bearings

•

Wheel profile to suit parallel or tapered flanges

AVAILABLE OPTIONS

•

Marine specification

•

Special paint systems

•

Collision bumpers

•

UK Ex scheme or ATEX zone 1 specification

•

Chain collectors ( PVC, galvanised or stainless steel)

•

Articulated trolley

•

Low headroom units

•

Rack & pinion drive

•

Travel limits

•

Air service units

•

Festoon systems

•

Radio control remote

•

Optional travel speeds

•

Beam brake

The

TCS-500-AT2S

is a 500 kg high speed chain hoist and trolley

from Red Rooster Lifting. This is part of our air hoist and trolley range

for lifting equipment applications in industry.

The

Red Rooster Lifting

TCS series of air hoists and

trolleys offer a range of high speed, lightweight

lifting equipment suited to all types of industrial

and marine environments. Red Rooster Lifting

hoists are the perfect lifting solution for where the

duty is high, or where a robust hoist is required to

withstand harsh conditions. The hoist and trolleys

comply with the UK supply of Machinery (Safety)

Regulations 2008 and the European Machinery

Directive. The hoists can be UKCA marked or CE

marked.

UK EX SCHEME ZONE 2

ATEX ZONE 2

AS STANDARD

RAISING EXPECTATIONS

Summary of Contents for TCS-500-AT2S









































































Search results

Summary of Contents for TCS-500-AT2S

Reviews:

Related manuals for TCS-500-AT2S

Brands by name

Popular brands

RED ROOSTER TCS-500-AT2S, User Manual

Search results

Summary of Contents for TCS-500-AT2S

Reviews:

Related manuals for TCS-500-AT2S

Brands by name

Popular brands