RED ROOSTER RRG-3630, Manual

Page: 5 / 8

Never wear loose clothing, wear suitable clothing otherwise it can be trapped causing injuries.
Only use accessories for this tool that are designated for this tool by its manufacturer.
Never aim the spark tail at yourself or other persons.
Convince yourself that no persons are in the working zone or danger zone.
The advised minimum age for operating this tool is 18 years.
Keep away from whipping hoses, this can cause injuries. A broken air hose or a hose that comes loose of the hose joint can start
whipping. Shut down the air supply immediately. In case the air hose is damaged, stop working, shut down the air supply and replace
the hose.
Keep the work place clean and organized, you may stumble and fall over a hose on the floor. Slippery floors and objects on the floor
are major causes of injuries.
This tool is not intended for use in potential hazardous areas and is not insulated from coming into contact with electric power.
In case that during the use of this tool dust is generated by either the process or the exhaust air blowing on dust in the environment, a
risk assessment has to made. Operator must use appropriate protection to prevent inhalation or skin contact. According to health and
safety regulations dust suction systems should be useded if possible and be maintained according manuafacturer's instructions.
Wear the appropriate clothing to feel comfortable at the workplace.
Cold exhaust air should be diverted from hands and body.
Air under pressure can cause injuries, be aware of this.
Never direct the exhaust air to yourself or anyone else.
Do not use quick change couplings direct on the air inlet of the tool as these may release during operation. Assemble at least 50 cm
air hose with a hose joint of shock resistant material.
In case universal twist couplings ( claw couplings) are used, the lock pins must be mounted.
Do not exceed the maximum air pressure as indicated on the tool.
Never carry the tool by the air hose.
On overhead work, use safety helmet.
Due to the process, the work piece, inserted/mounted tool/accessory may get hot causing burning injuries: Be aware of this.
A high force on the tool may cause high reaction forces on the tool.
Only use air hoses that are designed for it and are resistant against the used air pressure.
Check that sparks and debris can not cause any hazard.
Check the abrasive product on damages after it dropped.
Accessories
In order to (dis)assemble the sanding belt: Push the front wheel backwards in the locking device, change the belt, unlock the locking
device.
If the belt is not centered in the middle of the front wheel; correct this by adjusting the hexagon bolt on the right side, close to the front
wheel. Do this while the tool is running.
The rpm is adjustable with the adjustment screw at the bottom side of the handgrip on place of the lever.
The sanding arm can be adjusted in any position. Fix the position with the hexagon screw.
Check the rotation direction of the sanding belt when assembling. A wrongly assembled belt can break on the joint of the belt.
Select the best available inserted/mounted accessories/consumables for the lowest possible noise level and vibration. Replace them in
case of an increased noise level and/or vibration.
Make sure that the inserted/mounted abrasive is inserted/mounted correct and clamped.
After inserting/mounting an abrasive, let the tool run at no load in a safe direction for one minute, stop immediate at not normal
vibrations/noise and correct this or replace the abrasive.
Select the correct abrasive dimensions, rpm and spindle fitting for this tool.
Inspect the abrasive product on damages, cracks or other defects before mounting it on the tool.
Spindle fitting of the abrasive must be correct, do not use any kind of adaptor to fit the abrasive.
Flanges for mounting the abrasives must be in good condition without cracks and spindle and spindle threads are not damaged.
Use the inserted/mounted accessory/tool according to the manufacturer specifications.
Using the tool:
Before start using the tool, make sure that you are familiar with the workplace and surrounding area.
Always obey the safety regulations for the work area you are working in.
Hold the tool always firmly with both hands.
Start the tool by unlocking the safety lever and pushing the main lever.
Apply sufficient force, never supply too much force as this will slow down the efficiency. Maximum efficiency during operation: 80 % of
the free rpm.
Too much force may stop the tool.
During operating the tool, the operator may be exposed to hazards as crushing, impacts, heat, vibration, cuts, abrasions, etc: Wear
suitable gloves.
Any person handling the tool must be able to handle the size, weight and power of the tool.
Always be prepared for normal/abnormal movements/forces generated by the tool.
Keep your body in balance, place your feet safe and secure.
In case of interruption of the air supply, release the lever/trigger.
Take care of the reaction forces, if the tool (suddenly) stalls.
When using a power tool, you may experience discomfort in your hands, arms, shoulders, neck and other parts of your body.