background image

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship 
for a period limited to two years from the date of shipment, provided the products have been stored, 
handled, installed, and used under proper conditions. The Company’s liability under this limited 
warranty shall extend only to the repair or replacement of a defective product, at The Company’s 
option. The Company disclaims all liability for any affirmation, promise or representation with 
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against 
damages, claims, and expenses arising out of subsequent sales of RLC products or products 
containing components manufactured by RLC and based upon personal injuries, deaths, property 
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be 
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety 
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty 
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those 
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained 
herein and relies on no other warranties or affirmations.

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839

Red Lion Controls

China

Unit 101, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel +86 21 6113-3688

Fax +86 21 6113-3683

Red Lion Controls

Europe

Printerweg 10

NL - 3821 AD Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls

India

54, Vishvas Tenement

GST Road, New Ranip,

Ahmedabad-382480 Gujarat, India

Tel +91 987 954 0503

Fax +91 79 275 31 350

Summary of Contents for PAXLI









Reviews: