background image

1

2.00 (50.8)

1.10 (27.9)

0.11 (2.8)

0.10 (2.5)

1.56 (39.6)

0.87 (22.0)

0.874 

1.77 

(22.2      )

(45      )

+0.024

-0.000

+0.6

-0.0

+0.012

-0.000

+0.3

-0.0

85374216

    3 (8 Digit 0.35") LCD DISPLAY OPTIONS (Reflective, Red 

Transmissive, Yellow/Green Transmissive. 9 to 28 VDC power 
supply required for versions w/ LED backlighting)

    AVAILABLE VOLTAGE INPUTS (10 TO 30 VAC/DC)

    PRESCALER FROM 0.0001 TO 1.9999

  SELECTABLE DECIMAL POINTS

    REPLACEABLE INTERNAL LITHIUM BATTERY PROVIDES UP 

TO 6 YEARS OF UNINTERRUPTED OPERATION (Battery Included)

    WIRE CONNECTIONS VIA SCREW CLAMP TYPE TERMINALS

    FRONT PANEL AND REMOTE RESET INPUT

    NEMA 4X/IP65 SEALED FRONT BEZEL

    BOTH FRONT PANEL PROGRAM AND RESET BUTTONS ARE 

INDIVIDUALLY ENABLED

DESCRIPTION

The CUB7P3 is an 8-digit miniature programmable counter with large 0.35 

inch (8.90 mm) high digits. It has an LCD read-out available in Positive Image 
Reflective, Negative Image Transmissive with yellow/green backlighting, or red 
backlighting. Backlight units require an external 9 to 28 VDC power supply. 
The CUB7P3 versions operate from a signal voltage of 10 to 30 V (AC 50/60 
Hz or DC).

The CUB7P3 has a programmable prescaler that can be set for any value 

between 0.0001 and 1.9999. The decimal point position can be set anywhere 
from 0 (no D.P.) to 0.000000 or no Leading Zero Blanking. Both the prescaler 
and DP selection are accessed using the front panel PGM and RESET push 
buttons. See Programming for details. Note that the count, prescaler and DP 
values will be lost if the battery is removed. See BATTERY INSTALLATION 
for additional information.

The CUB7P counters use a CMOS LSI chip, mounted on a gold-plated 

substrate, that is electrically connected by ultrasonic wire-bonding. Proven 
micro-electronic assembly and manufacturing techniques provide these units 
with the reliability and dependability required for industrial service.

The CUB7P series is housed in a lightweight, high impact plastic case with a 

clear viewing window. The sealed front panel with the silicone rubber buttons 
meets NEMA 4X/IP65 specifications for wash-down and/or dusty environments, 
when properly installed.

SAFETY SUMMARY

All instructions that appear in the bulletin or on equipment, all safety related 

regulations, and all local codes must be observed to ensure personal safety and 
to prevent damage to either the instrument or equipment connected to it. If 
equipment is used in a manner not specified by the manufacturer, the protection 
provided by the equipment may be impaired.

MODEL CUB7P3 - PROGRAMMABLE  ELECTRONIC 8-DIGIT COUNTER

DIMENSIONS  In inches (mm)

Note: Recommended minimum clearance (behind the panel) for    mounting clip installation

is 2.1" (53.4) H x 5.5" (140) W.

PANEL CUT-OUT

Bulletin No.  CUB7P3-X(1)
Drawing No.  LP0700
Released  06/09

Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net

BNL10000

CUB7P320

CUB7P310

CUB7P300

PART NUMBER

Counter; Positive Image Reflective

Counter, w/Yel-Grn Backlighting

Counter; w/Red Backlighting

Replacement 3 V Lithium Battery

BNL

VOLTAGE

 INPUT

*CUB7P3

DESCRIPTION

MODEL NO.

* Battery is included with unit.

ORDERING INFORMATION

CAUTION: Risk of Danger.

Read complete instructions prior to 

installation and operation of the unit.

Summary of Contents for CUB7P3

Page 1: ...attery is removed See BATTERY INSTALLATION for additional information The CUB7P counters use a CMOS LSI chip mounted on a gold plated substrate that is electrically connected by ultrasonic wire bonding Proven micro electronic assembly and manufacturing techniques provide these units with the reliability and dependability required for industrial service The CUB7P series is housed in a lightweight h...

Page 2: ...mal point position is displayed Press the PGM button to select that position and return to the counter mode Remove the wire from the HS Program Enable terminal to prevent accidental changes to the programmed values Note The incrementing edge of the count signal will change when the PGM button is pressed for the first time To avoid incorrect display information it is recommended that the CUB7P be r...

Page 3: ...ed panel The viewing window and reset button are factory sealed for a washdown environment A sponge rubber gasket and mounting clip are provided for installing the unit in the panel cut out The following procedure assures proper installation 1 Cut panel opening to specified dimensions Remove burrs and clean around panel opening 2 Carefully remove and discard the center section of the gasket 3 Slid...

Page 4: ...umber of Pulses The number of pulses required to achieve the Desired Display Decimal Point Value The desired decimal point placement on the display Example Display tenths of inches when using Prescaler Desired Display Units x Decimal Point Value Number of Pulses 10 50 0 2 BACKLIGHT OPTION Optional backlight versions of the CUB7P require an external 9 to 26 VDC power supply The external supply is c...

Reviews: