RED CAT TEAL Golden Eagle Operator'S Manual Download Page 66

Page: 66 / 76

CAMERA DOES NOT HOLD STEADY

If in the air, wait 30 seconds. The gimbal will

automatically try to stabilize itself.

Restart the Golden Eagle by powering it off
and then on again.

Make sure that there are no obstructions or

debris in the gimbal payload.

The camera payload on the Golden Eagle “flops”

and will not hold stable.

A BATTERY PACK SHUTS OFF AFTER AN
ATTEMPT TO POWER ON

A battery pack that is NOT connected to a

Golden Eagle or TAC immediately shuts off after
an attempt to power it on.

This is normal behavior. The battery pack will

remain powered on once connected to a Golden
Eagle or TAC.

A battery pack that is connected to a Golden

Eagle or TAC will not power on or immediately
shuts off after an attempt to power it on.

Attempt to charge the battery pack:

Tap the power button once.

Insert the DC power cable into the charger and

plug the AC power cord into an AC outlet.

Insert the battery pack onto the charger.

Verify that the green LEDs on the battery pack

are illuminated to indicate the battery pack is

charging.

If the attempt to charge is unsuccessful, please
contact Teal Drone Customer Support:

(385) 281-8415

[email protected]

THE GOLDEN EAGLE WILL NOT ARM

Make sure that the battery pack is powered on

and is fully charged. The drone will not arm
when the battery pack charge level is 20% or

less.

If in Position Flight Mode, you may not be
connected to a sufficient number of satellites

to be able to triangulate the position of the

vehicle. It is critical to have at least eight (8)
but recommended that ten (10) satellites are

indicated on the GPS icon prior to takeoff.

The Golden Eagle will not arm using either the

arm button or soft key commands.

Summary of Contents for TEAL Golden Eagle













































































Search results

Summary of Contents for TEAL Golden Eagle

Reviews:

Related manuals for TEAL Golden Eagle

Brands by name

Popular brands

RED CAT TEAL Golden Eagle, Operator'S Manual

Search results

Summary of Contents for TEAL Golden Eagle

Reviews:

Related manuals for TEAL Golden Eagle

Brands by name

Popular brands