manualshive.com logo in svg

RED CAT TEAL Golden Eagle, Operator'S Manual, Page: 52 / 76

Share
Download
RED CAT TEAL Golden Eagle Operator'S Manual Download Page 52

51 

 

The Golden Eagle will arrive already calibrated, 

and needs to only be calibrated when: 

•

 

You  have  traveled  over  50  miles  (80 

km) or to a new geographical location. 

•

 

You  have  seen  significant  flight 

instability,  such  as  “toilet

-

bowling”  or 

horizontal position wandering greater 

than 10 ft (3 m). 

•

 

The  system  has  prompted  you  to 

perform a calibration. 

Follow along with our instructional video, 

Calibrating Drone Sensors: Teal Golden Eagle 

Drone

 on our website at: 

https://tealdrones.com/support/video/

 

 

CALIBRATING THE COMPASS 

Connect the drone and the TAC. 

Touch the MENU icon. 
Select VEHICLE SETUP. 

Select SENSORS. 
Select 

COMPASS 

to 

calibrate 

the 

magnetometer. 
Be ready to pick up and rotate the drone. 
Click OK in the top right of the screen to begin. 
The first tone from the Golden Eagle will alert 

you to begin.  
Follow the instructions on the TAC screen. 
The  second  tone  will  prompt  you  to  hold  the 

drone steady for the next orientation. 
Select REBOOT VEHICLE when finished. 

 

NOTE: Due to known errata, it is 
recommended  to  perform  a 

power  cycle  (turn  the  drone 

battery pack off and on again. 

Reestablish  connection  between  the  TAC  and 

the drone. 

 

CALIBRATING THE GYROSCOPE 

Connect the drone and the TAC. 

Touch the MENU icon. 

Select VEHICLE SETUP. 

Select SENSORS. 

Place the drone on a flat, level surface. 

Select GYROSCOPE. 

Click OK in the top right of the screen to begin. 

This  should  only  take  a  few  seconds  to 

complete. 

CALIBRATING THE ACCELEROMETER 

Connect the drone and the TAC. 

Touch the MENU icon. 

Select VEHICLE SETUP. 

Select SENSORS. 

Place the drone on a flat, level surface. 

Select ACCELEROMETER. 

Click OK in the top right of the screen to begin. 

Follow the instructions on the TAC screen. As 

each  orientation  completes,  move  the  drone 

into the next position as prompted on the TAC 
screen. When all six (6) positions are complete, 

you may exit to the fly screen. 

Summary of Contents for TEAL Golden Eagle













































































Reviews:

No comments