Record Power DP25B Original Instruction Manual Download Page 6

3. Record Power Guarantee

Products

” means the Products sold by Record Power subject to these terms 

and conditions;

Record Power

” is Record Power Limited, whose company registration 

number is 4804158 and registered office address is Centenary House,  
11 Midland Way, Barlborough Links, Chesterfield, Derbyshire, S43 4XA and sells 
through a network of Authorised Dealers;

Authorised Distributor

” is the nominated importer for your region who will 

generally sell through a network of Authorised Dealers. Details of Authorised 
Distributors for specific countries can be found in the Product manual or at 
www.recordpower.info;

Authorised Dealer

” is a retailer or business authorised to sell Record Power 

Products to end users. 

Guarantee 

1.1

    Record Power guarantees that for a period of 5 years from the date of 

purchase the components of qualifying Products (see clauses 1.2.1 to 
1.2.9) will be free from defects caused by faulty construction  
or manufacture.

1.2

    During this period Record Power, its Authorised Distributor or Authorised 

Dealer will repair or replace free of charge any parts which are proved to 
be faulty in accordance with paragraphs 1.1 above provided that:

1.2.1

  you follow the claims procedure set out in clause 2 below;

1.2.2

   Record Power, our Authorised Distributor or Authorised Dealer are given 

a reasonable opportunity after receiving notice of the claim to examine 
the Product;

1.2.3

   if asked to do so by Record Power, its Authorised Distributor or 

Authorised Dealer, you return the Product, at your own cost, to 
Record Power’s premises or other approved premises such as those 
of the Authorised Distributor or supplying Authorised Dealer, for the 
examination to take place;

1.2.4

   the fault in question is not caused by industrial use, accidental damage, 

fair wear and tear, wilful damage, neglect, incorrect electrical connection, 
abnormal working conditions, failure to follow our instructions, misuse, 
or alteration or repair of the Product without our approval;

1.2.5

   the Product has been used in a domestic environment only;

1.2.6

   the fault does not relate to consumable Products such as blades, 

bearings, drive belts or other wearing parts which can reasonably be 
expected to wear at different rates depending on usage (for full details 
contact Record Power or your local Authorised Distributor);

1.2.7

    the Product has not been used for hire purposes, by you or by a previous 

owner;

1.2.8

   the Product has been purchased by you as the guarantee is not 

transferable from a private sale. 

1.2.9

   where the Product has been purchased from a retailer, the 5 year 

guarantee is transferable and begins on the date of the first purchase of 
the Product and in the event of a claim under this guarantee proof of the 
original purchase date will be required to validate the warranty period.

Claims Procedure

2.1

    In the first instance please contact the Authorised Dealer who supplied 

the Product to you. In our experience many initial problems with 
machines that are thought to be due to faulty parts are actually solved 
by correct setting up or adjustment of the machines. A good Authorised 
Dealer should be able to resolve the majority of these issues much more 
quickly than processing a claim under  
the guarantee.

2.2

    Any damage to the Product resulting in a potential claim under the 

guarantee must be reported to the Authorised Dealer from which it was 
purchased within 48 hours of receipt.

2.3

    If the Authorised Dealer who supplied the Product to you has been 

unable to satisfy your query, any claim made under this Guarantee 
should be made directly to Record Power or its Authorised Distributor 
(for details of the Authorised Distributor in your country please see 
your Product manual or check www.recordpower.info for details). The 
claim itself should be made in a letter setting out the date and place of 
purchase, and giving a brief explanation of the problem which has led to 
the claim. This letter should then be sent with proof of the purchase date 
(preferably a receipt) to Record Power or its Authorised Distributor. If you 
include a phone number or email address this will help to speed up your 
claim.

2.4

   Please note that it is essential that the letter of claim reaches Record 

Power or its Authorised Distributor on the last day of this Guarantee at 
the latest. Late claims will not be considered.

Limitation of Liability 

3.1

    We only supply Products for domestic and private use. You agree not to 

use the Product for any commercial, business or re-sale purposes and we 
have no liability to you for any loss of profit, loss of business, business 
interruption or loss of business opportunity.

3.2

   This Guarantee does not confer any rights other than those expressly 

set out above and does not cover any claims for consequential loss or 
damage. This Guarantee is offered as an extra benefit and does not affect 
your statutory rights as a consumer.

Notice 

 

 

This Guarantee applies to all Products purchased from an Authorised 
Dealer of Record Power within the United Kingdom of Great Britain 
and Northern Ireland. Terms of Guarantee may vary in other countries – 
please check with the Authorised Distributor in your country (details of 
the Authorised Distributor for your country can be found in the manual or 
at www.recordpower.info).

Summary of Contents for DP25B





















Reviews: