ReChargx RX230X Instructions Manual Download Page 7

Page: 7 / 10

TonerRefillKits.com

RechargX™ RX230X v1

Mon - Fri 8am - 5pm ET

2011.11.09

Page 7 of 10

Step 14: Empty the Waste Toner Hopper

Now we will remove the waste toner from the

toner cartridge.

Note

: There is no need to attempt to remove

every last bit of waste toner from the hopper,

just that which comes out easily.

Note

: This toner cannot be used again as paper

dust, hair, staples and other small items can

accumulate in the waste hopper.

Holding the cartridge over the newsprint,

included in the ReChargX™ RX230X Toner

Refill Kit, carefully pour out any waste toner,

as shown in figure 15.

If the waste toner stops flowing, stand the

cartridge up again and then re-lower the hole

over the paper (gently tapping along the side

of the toner cartridge helps to keep the toner

flowing as well).

Step 15: Clean the Area Around the

Waste Hopper Hole

After the waste toner has been removed from

the waste hopper, use the yellow/orange toner

grabber cloth to clean around the waste hopper

hole, as shown in figure 16, so the ReChargX™

leak-proof seal will adhere to the cartridge body

as completely as possible.

Figure 15

: Empty the waste toner

Figure 16

: Clean the waste hopper hole

Summary of Contents for RX230X











Search results

Summary of Contents for RX230X

Reviews:

Related manuals for RX230X

Brands by name

Popular brands

ReChargx RX230X, Instructions Manual

Search results

Summary of Contents for RX230X

Reviews:

Related manuals for RX230X

Brands by name

Popular brands