ReChargx RX230X Instructions Manual Download Page 5

Page: 5 / 10

TonerRefillKits.com

RechargX™ RX230X v1

Mon - Fri 8am - 5pm ET

2011.11.09

Page 5 of 10

Step 9: Plug in the Hole-Making Tool

Plug in the hole-making tool included with the

ReChargX™ Tool Kit.

Turn the sand timer over and wait the full three

minutes before using the tool so it reaches

proper operating temperature; this ensures the

tool will easily penetrate the cartridge housing

(figure 10).

Step 10: Locate the Waste Hopper

Orient the cartridge on your work surface with

the handle of the toner cartridge closest to your

chest.

Next, rotate the cartridge 180 degrees away

from you so the cartridge is upside down with

the cartridge handle away from your chest.

The white arrows, in figure 11, show the

direction the toner cartridge must be turned

to locate the waste hopper.

Figure 10

: Wait for the hole-making tool to heat up

Figure 11

: Locate the waste hopper

Summary of Contents for RX230X











Search results

Summary of Contents for RX230X

Reviews:

Related manuals for RX230X

Brands by name

Popular brands

ReChargx RX230X, Instructions Manual

Search results

Summary of Contents for RX230X

Reviews:

Related manuals for RX230X

Brands by name

Popular brands