background image

User Note 

Alert Status 

Usually  people  enter  the  alert  status  after  1  minute  normal  driving,  but  some  people  who  wear 

glasses  need  take  at  most  5  minutes.  If  you  fall  asleep  after  the  system  enters  to  the  alert 

status,  the  RVS-350P  alarm  will  be  triggered.  If  there  are  large  movements  and  the  driver 

is talking  before  closing  their  eyes,  it  only  gives  them  one  or  two  friendly  reminding  alarm 

after your eyes close for 4-7 seconds. If the driver didn’t have big movement and didn’t speak, eyes 

open gets  smaller  and  smaller,  or  eyes  closed,  or  watching  the  front  but  in  thinking,  it  will  make 

sharp alarming after 2 seconds. 

After the product is connected to power supply for 2 seconds, the green light will flash for 1 second. 

At night the infra-red light turns red. In the first 30 seconds, the system detect the driver’s position 

and  analyzes  driver’s  condition,  it  does  not  make  warnings  during  this  period.  Only  after  the 

driver  has  been  keeping  driving  for  more  than  30  seconds,  the  system  will  enter  into  alert  status. 

However, once power is on, the system will detect if the driver’s eyes are open or not. If the green 

light is on, it means the driver’s eyes are open. If the green light is off, it means the driver closes 

eyes  or  driver  is  not  in  the  detecting  range  of  the  camera.  For  first  time  installation,  you  can 

adjust the camera’s position based on the green light’s display. 

The  RVS-350P  can  detect  and  analyze  the  driver’s  fatigue  condition  prior  to  falling  into 

sleep. Normally,  driver's  eyes  get  less  and  less  sensitive  to  the  light  before  falling  into  sleepy 

condition. At  this  time,  the  RVS-350P  is  detects  and  analyzes  the  driver’s  retina  condition, 

making  sharp  alarms  to  wake  the  driver  up  prior  to  them  falling  asleep.  The  driver 

should  stop  driving immediately and have a rest after being alerted by the RVS-350P. 

People Image Identification 

For certain populations the system needs 1-60 seconds to detect, if the green light turns on when the 

eyes open and the green light turns off when the eyes are closed, it is working properly.

Summary of Contents for RVS-350P










Reviews: