Realtree RTLS-502 Manual Download Page 17

Installation Straps, Ratchet Straps, Quickclips, 

Tiedown Ropes and Stabilizer Bars MUST be installed 

and secured prior to climbing tree stand. Failure to 

comply may result in serious injury or death.

W A R N I N G

ALWAYS 

read and understand all warnings and instructions 

before each use of this product. Failure to read and 

understand all warnings and instructions may result in 

serious injury or death.

ALWAYS

 inspect the tree stand for signs of wear or damage 

BEFORE 

each use. Also inspect to ensure that nuts and 

bolts are secure and straps are not frayed, worn, or broken.

ALWAYS

 wear a Fall Arrest System (FAS) after leaving the 

ground. If you are not wearing an FAS that meets ASTM 

standards, 

DO NOT leave the ground

. Failure to wear an 

FAS may result in serious injury or death.

DO NOT

 use this tree stand while under the influence of 

alcohol, medication, or illegal substances. Use of tree stand 

while under the influence of any of these substances may 

result in serious injury or death.

NEVER

 use this tree stand if you have a history of health problems 

such as 

(but not limited to) 

heart problems, back problems, 

impaired vision, equilibrium impairments are afraid of heights or 

have been advised by a doctor not to do any strenuous activity. If 

you are feeling ill, nauseous, or dizzy 

DO NOT

 use this tree stand 

or If you are not physically fit, well rested and alert. Physical 

ailments can reduce your ability to safely install, utilize and remove 

your tree stand.

NEVER

 use this tree stand during inclement weather such as (but 

not limited to) thunderstorms, snowstorms, hurricanes, icy 

conditions, or high winds that could create slippery or dangerous 

situations.

NEVER

 use this tree stand on a dead, leaning, loose 

barked tree or on a utility pole as the tree may fall, break, 

or uproot and may result in serious injury or death.

DO NOT

 modify or alter your tree stand.

NEVER

 leave the ground without checking every ladder 

section connection to ensure they are firmly connected. If 

ladder sections are separating, with the help of at least two 

other people, remove the tree stand from the tree, tighten 

all connections and reinstall on the tree.

NEVER

 remove or deface warning labels. 

DO NOT 

use treestand if combined weight of one person 

and equipment exceeds 

300 lbs

. or combined weight of two 

people and equipment exceed 

500 lbs

DO NOT exceed 

the weight limit of safety harness, refer to harness 

manufacturers warnings for weight limit of  safety 

harness

.

Failure to follow all warnings listed below could result in serious injury or death.

Manufactured in the year 2019 

Primal Vantage Company Inc. 2407 W. Euclid Ave., Littleton, CO  80120 1-866-972-6168

DO NOT

 climb ladder without Stabilizer Bar or Installation 

Straps installed. This 

MUST

 be correctly installed prior to 

use. Serious injury or death may occur if Stabilizer Bar 

and Installation Straps are not installed.

W A R N I N G

Summary of Contents for RTLS-502


















Reviews: