Real Flame Captiva 900 Installation & Operating Manual Download Page 3 | Manualshive

Page: 3 / 51

background image

2 |

P a g e

WARNING

The Inspire space heater has a primary safety glass fitted in front of the glass door. This safety glass is fitted to
this appliance to reduce the risk of injury from burns and at no time should this glass be permanently removed.

For protection of young children or the infirm, a secondary guard is required.

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.

WARNING

The outer glass panel gets extremely hot! Precaution should be taken and young children supervised at all
times when heater is operating

INSTALLATION NOTICE



The installation of this appliance is only to be carried out by an authorized person in accordance with
the Manufacturer’s Instructions, local gas fitting regulations, AS/NZS5601.1-2013 installation code for
gas burning appliances and any other relevant statutory regulations.



Do not modify this appliance



In all cases the installation of this appliance shall meet the requirements as set out in AS/NZS5601.1-
2013.



Do not install in a fireplace as a Type 1 installation.

NOTE: A slight smell may be apparent for the first few hours of use. This is due to the heat resistant paint
curing. It is recommended to open windows in the room for the first lighting of the fire. In some instances, a
slight discolouration may occur inside the firebox. This is a normal condition and is not covered by warranty.

IMPORTANT SAFETY NOTICE



DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.



DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE



DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN OPERATION



CARE MUST BE TAKEN TO ENSURE THAT ANY RETURN AIR REGISTER OR EXHAUST SYSTEM DOES NOT
ADVERSLEY AFFECT THE OPERATION OF THE APPLIANCE OR DRAUGHT OF CHIMNEY OR FLUE.



APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOUS FLAMES. MAY EXHIBIT SLIGHT CARBON
DEPOSIT

SERVICING

It is recommended you service your gas fire every 2 years as a minimum.

CORD REPLACEMENT

Electrical cord replacement must be undertaken by qualified and trained personnel only

«
1
2
3
4
5
...
»

Summary of Contents for Captiva 900




















































Reviews:

No comments

Related manuals for Captiva 900

Brand: Lasko Pages: 6

Brand: U-Line Pages: 3

Brand: Zodiac Pages: 60

Brand: A.O. Smith Pages: 4

Brand: Nibe Pages: 20

Brand: Qlima Pages: 45

Brand: INNOLIVING Pages: 14

Brand: Haverland Pages: 71

Brand: Nibe Pages: 56

Brand: Enviro Pages: 112

Brand: Versonel Pages: 12

Brand: Inelco Pages: 23

Brand: Comfort Glow Pages: 6

Brand: Dometic Pages: 4

Brand: Smith's Heating First Pages: 2

Brand: Electric House Pages: 15

Brand: Amtrol Pages: 2

Brand: BioSmart Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands