RDZ WHR 60 Page 14 Technical And Installation Manual Download | Manualshive

Page: 14 / 21

background image

33

MAINTENANCE

All maintenance operations must only be done by qualified person.
Before carrying out any cleaning or maintenance disconnect the main supply.

Once installed, the product must have the components placed exactly as shown in the picture
here above.

1) MAINTENANCE PERIOD INDICATIONS

We recommend to clean the filters (8) and the ceramic exchanger (7) every 3 months.
We recommend to change the filters every 2 years. You can get the replacement through the
retailer

.

Every 2000 hours of operation the product stops running and the indicator light placed in the
bottom right will give a steady red light signal.
Clean the filters and the ceramic exchanger as specified in the paragraph. Replace the filters when
necessary.

«
...
12
13
14
15
16
...
»

Summary of Contents for WHR 60






















Reviews:

No comments

Related manuals for WHR 60

Brand: Salda Pages: 89

Brand: Zehnder Rittling Pages: 8

Brand: Vents Pages: 20

Brand: Hallowell Pages: 40

PreciseLine Series

Brand: Daikin Pages: 122

Brand: Fedders Pages: 16

Brand: Genex Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands