background image

Programming Codes

For basic operation, see the Quickstart guide on page 1. 

Programming additional features in the keypad are shown below.

Enter the 6 digit master code

Select an option by pressing a number and holding it down for 3 seconds

0

1

2

3

4

5

6

7

8

9

Turns backlight on or off

    

       = ON           = OFF*

*

#

Type of release          = fail unlocked release           = fail locked release*

*

#

Multi user codes (up to 120)           = ON           = OFF*

Remember to delete the factory user 7890 after entering multi-user codes

*

#

Sound          = OFF           = ON*

*

#

Lockout for 60 Seconds after 20 incorrect keystrokes         = ON         = OFF*

*

#

Door open time in Seconds - enter 2 digits from 01 to 60 (Default is 7 sec)

Change master code - enter new 6 digit code        re-enter code

*

*

Exit button operation           = Normal*         = Toggle         = Disabled 

User codes  - enter user code 4-8 digits         re-enter code
 
                       - press          to confirm code as normal code
                       - press          to confirm code as a toggle code
                       - press          to delete this user code

*

*

1

2
3

Data reset - Re-enter the master code - Press and hold        for 3 Seconds.

 9

This returns all the settings (except multi-user) to the factory defaults with a 

single user code of 7890. This does not change the master code.

1

2

3

Exit programming mode

* = Factory defaults

#

©2010 RUTHERFORD CONTROLS INT’L CORP. WWW.RUTHERFORDCONTROLS.COM

USA: 2697 INTERNATIONAL PARKWAY, PKWY 5, VIRGINIA BEACH, VA 23452 • CANADA: 210 SHEARSON CRESCENT, CAMBRIDGE, ON  N1T 1J6 

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-MAIL: [email protected]

9325 Keypad Installation Instructions 

(Continued)

3

Summary of Contents for 9325









Reviews: