RCF P3108 User Manual Download Page 11

11

ENGLISH

10.

 There  are  numerous  mechanical  and  electrical  factors  to  be  considered  when  installing 

a  professional  audio  system  (in  addition  to  those  which  are  strictly  acoustic,  such  as  sound 
pressure, angles of coverage, frequency response, etc.).

11.

 Hearing loss

 

Exposure to high sound levels can cause permanent hearing loss. The acoustic pressure level 
that leads to hearing loss is different from person to person and depends on the duration of 
exposure.

 

To prevent potentially dangerous exposure to high levels of acoustic pressure, anyone who is 
exposed to these levels should use adequate protection devices.

 

When a transducer capable of producing high sound levels is being used, it is necessary to wear 
ear plugs or protective earphones.

 

See the technical specifications in the instruction manual for the maximum sound pressure the 
loudspeaker is capable of producing.

12.

 To ensure a correct sound reproduction, loudspeaker phase is to be respected (loudspeakers are 

connected respecting the amplifier polarity). This is important when loudspeakers are installed 
adjacent one another, for instance, in the same room.

13.

 To prevent inductive effects from causing hum, noise and a bad system working, loudspeaker 

lines  should  not  be  laid  together  with  other  electric  cables  (mains),  microphone  or  line  level 
signal cables connected to amplifier inputs.

14.

 The  loudspeaker  cable  shall  have  wires  (twisted,  if  possible,  to  reduce  inductive  effects 

due  to  surrounding  electro-magnetic  fields)  with  a  suitable  section  and  a  sufficient  electrical 
insulation. Refer to local regulations since there may be additional requirements about cable 
characteristics.

15.

 Do NOT connect the loudspeaker low impedance (8 Ω) input to 100 V constant voltage lines.

16. 

Install this loudspeaker far from any heat source.

17. 

Do not overload the loudspeaker with too much power.

18. 

Do not use solvents, alcohol, benzene or other volatile substances for cleaning the external parts 

of this product.

Summary of Contents for P3108

















Reviews: