background image

8

TROUBLESHOOTING

NO SOUND - Make sure the AC adapter is fully inserted into the AC 

outlet and into the DC Power Jack input on the 
transmitter.

- Make sure the headphone ON/OFF switch is in the

ON position.

- Headphone battery may be too weak. Charge battery.  

Charge the new batteries for 24 hours prior to the first 
use.

- Make sure the TV, stereo receiver or audio component 

is ON and tuned to a channel with audio.

- Adjust the volume control on the headphone to 

increase the volume.

- The connected audio/video equipment is not playing.  

Turn on the equipment.

- The volume of the headphones is turned down. 

Adjust the volume to an appropriate level.

DISTORTED  - Make sure the stereo indicator light is ON.  If not, adjust

the tuning wheel on the headphone until the indicator 
light is on. 

- Turn the FREQUENCY ADJUST control to change 

operating frequency of transmitter. You must then press
the “Auto Scan” button on the headphone until the 
stereo indicator lights.

- Headphone batteries may be too weak. Charge the 

batteries or replace with the new batteries.

- The headphone is too far from transmitter (over 150 

feet). Move closer.

- The input level of the audio signal is too low. Turn up

the volume of the audio source equipment.

WHP160/WHP160T_IB  11/5/01  10:09 AM  Page 8

Summary of Contents for WHP160











Reviews: