background image

EN

23

Troubleshooting Tips

Troubleshooting Tips

Receiver/Tuner Operation 

ST indicator is off.

•  Adjust the antenna.
•  Press 

GO BACK/ST.MONO

button to insure you 

are not outputting in mono.

The signal is Mono. Severe hum or noise.

•  The signal is too weak. Connect an external antenna.
• Adjust Antenna
•  Reposition Antenna away from any electronics.

There is interference to FM reception.

•  Turn off other electrical units (e.g. DVD, CD player) 

near the receiver.

• Reposition the Antenna.

Remote Control Operation 

The remote control does not operate the unit.

•  Another source mode is selected on the remote. Press 

the correct Source Button.

•  No batteries installed. (included with your system) 

Install the batteries before attempting to operate the 
remote. Be sure to match the + and - ends of each 
battery to the symbols shown in the remote battery 
compartment.

•  The batteries are weak. Replace all batteries.
•  The remote is not pointed at the remote control 

sensor on the main unit or there is an obstacle 
between the remote and the main unit.

•  The remote control is too far from the main unit, 

move closer.

Remote loses Programmed codes.

•  Weak batteries, replace batteries.

Remote forgets what source was selected.

•  Weak batteries, replace batteries.

General 

No audio.

•  Make sure the speakers are connected.
•  Check the input connections.
•  Check the power cord connections.
• Make sure the MUTE signal on the front panel is off.
•  Make sure the digital setting (optical, coaxial or 

analog) is correct. 

•  Check that the headphone is not inserted.

No audio from one channel.

•  Check the speaker level setting.
•  Check the speaker wire or external source cable 

connections. 

•  Check whether the center or surround speaker 

settings are set to YES.

Noise occurs when the TV is turned on.

•  The TV is too close to the audio system. 

Specific instruments sound displaced.

•  Check the connections between the receiver and the 

speakers if the sound does not match the video.

•  Check if the video and audio cable are correctly 

inserted.

TAPE OUT and REC OUT do not operate in VCR
mode.

•  Check to make sure analog input signal is connected 

from the signal source to the analog input jacks.

• In VCR mode, VCR OUT will be muted.
• In TAPE mode, TAPE OUT will be muted.

Cleaning the Exterior

Disconnect the system from AC power before cleaning
the exterior of the system with a  soft dust cloth, or
with a slightly damp leather chamois. Never use strong
solvents.

RT2620  EN  4/7/04  1:42 PM  Page 27

Summary of Contents for RT2620






























Reviews: