background image

4

On the open end of the middle (large) 
section, remove the rear nut and screw.

Find the rear section. Slide the narrow 
boom of the rear antenna into the middle 
(large) section. Tap lightly with a rubber 
mallet on the end of the small boom, 
aligning the holes for the screw. (See fi gure 
6.)

Re-install the screw and nut; be sure to 
tighten securely.

Step 6:   Connect the rear section to the middle 

(large) section

Rear 

section

Middle 

section

Screw

Nut

Fig. 6

Step 7:   Connect the phasing lines

On the middle (large) section, near where 
the middle and rear sections come 
together, fi nd the posts on the top and 
bottom of the last element holder studs. 
(See fi gure 7.)

Place the phasing lines from the rear 
section over the studs, one on the top side 
and one on the bottom. Then fasten them 
to the posts with washers and #10 fl ange 
nuts. Tighten securely.

Nut

Washer

Stud

Phasing 
line

Fig. 7

13

Paso 8: Conecte el sujetador del brazo  

Coloque el sujetador del brazo en la parte superior de la antena. Asegúrese 
que las abrazaderas del mástil (las secciones color latón) del sujetador del 
brazo y la antena estén orientadas en la misma dirección. 

Ubique el orifi cio para el tornillo en el brazo 
del refl ector y fi je el sujetador con una de 
las tuercas y tornillos #10 suministrados. 
(Consulte la fi gura 8.) 

Tornillo

Tuerca

Fig. 9

Fig. 8

Paso 9: Instale el transformador

Encuentre la conexión del conductor en la parte inferior de la sección frontal 
de la antena, justo detrás de los brazos del refl ector. 

Coloque dos arandelas en cada prisionero con rosca. Coloque una tuerca #10 
sobre cada prisionero con rosca, pero no la apriete todavía. 

Coloque los extremos del transformador entre las dos arandelas y apriete bien 
las tuercas. (Consulte la fi gura 10.) Fije el conductor de conexión coaxial al 
transformador.

Transformador

Conexiones 

del 

conductor

Fig. 10

Gire el sujetador del brazo hacia abajo y 
hacia atrás. Forme una “V” con las bandas 
de metal. Utilice una de las tuercas y tornillos 
#10 suministrados para fi jar la “V” a cada 
lado del brazo. (Consulte la fi gura 9.)

Español

Summary of Contents for ANT3038XR









Reviews: