background image

16

Electrode Size

  Average Thickness  Maximum Recommended  

 

of Material 

Electrode Diameter

  0.03 - 0.07 inches 

0.09 inches 

  0.07 - 0.19 inches 

0.12 inches 

  0.19 - 0.31 inches 

0.15 inches 

  0.31 -  >  inches 

0.19 inches 

The size of the electrode generally depends on the 

thickness of the section being welded, and the thicker 

the section the larger the electrode required. The table 

gives the maximum size of electrodes that maybe used 

for various thicknesses of section based on using a  

general purpose type 6013 electrode.

Correct current selection for a particular job is an  

important factor in arc welding. With the current set too 

low, difficulty is experienced in striking and maintaining 

a stable arc. The electrode tends to stick to the work, 

penetration is poor and beads with a distinct rounded 

profile will be deposited. Too high current is  

accompanied by overheating of the electrode resulting 

undercut and burning through of the base metal and 

producing excessive spatter. Normal current for a particular job may be considered as the maximum, which 

can be used without burning through the work, over-heating the electrode or producing a rough spattered 

surface.The table shows current ranges generally recommended for a general purpose type 6013  

electrode. 

 

Arc Length

To strike the arc, the electrode should be gently scraped on the work until the arc is established. There is a 

simple rule for the proper arc length; it should be the shortest arc that gives a good surface to the weld. An 

arc too long reduces penetration, produces spatter and gives a rough surface finish to the weld.  

An excessively short arc will cause sticking of the electrode and result in poor quality welds. General rule of 

thumb for down hand welding is to have an arc length no greater than the diameter of the core wire. 

Electrode Angle

The angle that the electrode makes with the work is important to ensure a smooth, even transfer of metal. 

When welding in down hand, fillet, horizontal or overhead the angle of the electrode is generally between 5 

and 15 degrees towards the direction of travel.  When vertical up welding the angle of the electrode should 

be between 80 and 90 degrees to the work piece. 

 

Travel Speed

The electrode should be moved along in the direction of the joint being welded at a speed that will give the 

size of run required. At the same time, the electrode is fed downwards to keep the correct arc length at all 

times. Excessive travel speeds lead to poor fusion, lack of penetration etc, while too slow a rate of travel 

will frequently lead to arc instability,slag inclusions and poor mechanical properties. 

 

Material and Joint Preparation

The material to be welded should be clean and free of any moisture, paint, oil, grease, mill scale, rust or 

any other material that will hinder the arc and contaminate the weld material. Joint preparation will depend 

on the method used include sawing, punching, shearing, machining, flame cutting and others. In all cases 

edges should be clean and free of  any contaminates. The type of joint will be determined by the chosen 

application.

Welding Current (Amperage)

 

Electrode Size 

Current Range  

 

ø mm 

(Amps)

 

0.09 inches 

60 - 100 

 

0.12 inches 

100 - 130 

 

0.15 inches 

130 - 165 

 

0.19 inches 

165 - 260 

Electrode Selection

As a general rule, the selection of an electrode is straight forward,in that it is only a matter of selecting an 

electrode of similar composition to the parent metal. However, for some metals there is a choice of several 

electrodes, each of which has particular properties to suit specific classes of work. It is recommend to  

consult your welding supplier for the correct selection of electrode.

MMA (Stick) Welding Fundamentals

Summary of Contents for KUMJRRW160





































Reviews: