manualshive.com logo in svg

Raytec VAR2 IPPOE i4-1, Full Installation And Setup Manual, Page: 62 / 64

Share
Download
Raytec VAR2 IPPOE i4-1 Full Installation And Setup Manual Download Page 62

 

 

 

62 

 

Raytec APIs (VMS and HTTP) 

The Raytec Network Illuminator has been designed such that it can be integrated into 

3

rd

 party systems such as a VMS, BMS  etc. as well as receiving HTTP commands and 

Raytec  have  suitable  APIs  to  support  such  integrations.  Please  contact  Raytec  to 

discuss your particular requirements. 

For full documentation to support API implementation, please contact Raytec.  

Troubleshooting & FAQs 

Typical Questions: 

 

Please see Basic Troubleshooting on pages 20-21 
 

Also, please feel free to contact us directly on the contact numbers below. 

 

 
Can I run the illuminator from auxiliary power? 

– Yes, VARIO2 IPPoE can be operated 

from PoE power or 24V DC. See page 4.

 

 
What PoE cable type is compatible? 

– Use CAT 5 or CAT 6 cable with T-568B wiring 

standard.

 

 
What  is  a  suitable  Power  Sourcing  Equipment  for  IP? 

–  VARIO2    IPPoE  4  is  .at 

compliant and requires 25.5W minimum. VARIO2 IPPoE  8 requires an .at handshake 
and power of 51W minimum.

  

 
I have forgotten my Password. 

– If you are an operator, contact your administrator. If 

you  are  an  administrator,  then  you  may  need  to  perform  a  hard  reset  of  the 
illuminator – see previous page.

 

 
I cannot discover my illuminator on the network using the Raytec Discovery Tool. 

– 

Check that there is power to the illuminator, check that the correct CAT 5 / 6 wiring is 
being used, check that your computers Firewall is allowing the illuminator access and 
is not blocking UDP traffic. 
 

 

Summary of Contents for VAR2 IPPOE i4-1

































































Reviews:

No comments