background image

To Open the Door Manually

The door should be fully
closed if possible. Pull down
on the emergency release
handle and lift the door
manually. To reconnect the
door to the opener, press the
door control push bar.

The 

lockout feature

prevents

the trolley from reconnecting
automatically. Pull the
emergency release handle
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage the
lockout feature, pull the
handle straight down. The
trolley will reconnect on the
next UP or DOWN operation,
either manually or by using
the door control or remote.

To prevent possible SERIOUS INJURY or DEATH from a
falling garage door:

• If possible, use emergency release handle to

disengage trolley ONLY when garage door is CLOSED.
Weak or broken springs or unbalanced door could
result in an open door falling rapidly and/or
unexpectedly.

• NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

• NEVER use handle to pull door open or closed. If

rope knot becomes untied, you could fall.

27

Trolley
Release 
Arm

NOTIC

E

Emergency
Release 
Handle
(P

u

ll Do

w

n)

Trolley
Release 
Arm

NOTICE

Emergency
Release Handle
(Do

w

n and Back)

WARNING

CAUTION

WARNING

WARNING

LOCKOUT POSITION

MANUAL DISCONNECT

POSITION

Using the Wall-Mounted 
Door Control

THE MULTI-FUNCTION DOOR CONTROL

Press the push button to open or
close the door. Press again to
reverse the door during the closing
cycle or to stop the door while it's
opening.

Light feature

Press the Light button to turn the opener light on or
off. It will not control the opener lights when the door
is in motion. If you turn it on and then activate the
opener, the light will remain on for 4-1/2 minutes.
Press again to turn it off sooner. The 4-1/2 minute
interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button
until the light blinks (about 10 seconds). A single blink
indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice,
resetting the timer to 2-1/2 minutes. Repeat again for
a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.

Lock feature

Designed to prevent operation of the door from 
hand-held remote controls. However, the door will
open and close from the Door Control, the Outside
Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The
Lock feature will also turn off whenever the “learn”
button on the motor unit panel is activated.

LOCK

LIGHT

P

u

sh 

B

u

tton

Lock 
B

u

tton

Light
B

u

tton

Summary of Contents for Navigator 2245RGD





































Reviews: