manualshive.com logo in svg

Raycus RFL-P500H, User Manual, Page: 15 / 28

Share
Download
Raycus RFL-P500H User Manual Download Page 15

Wuhan  Raycus  Fiber  Laser  Technologies  Co.,  Ltd. 

User Guide of RFL-P500H

 

13

 

 

4.2

 

Rear Panel 

Figure 5 shows the rear panel: 

 

Figure 5 Rear Panel

 

1.

 

INPUT: 

The socket for power supply input that can be only mated with the 

plug  on  the  power  cord  Raycus  provided.The  socket  is  provided  with  a 

protective cover and a lock catch. Please use the protective cover and lock 

catch when not use the laser device.

 

2.

 

POWER:

 Air switch. Controlling the on-off of AC.

 

3.

 

Control  INTERFACE: 

Control  interface.  Users  can  control  the  laser  via 

this interface. Please reference table 4.4.2 for specific definition of control 

signal.  The  socket  is  provided  with  a  protective  cover  and  a  lock  catch. 

Please  use  the  protective  cover  and  lock  catch  when  not  use  the  laser 

device. 

4.

 

RS-232: 

RS-232  interface.  Users  can  control  the  laser  by  command  via 

RS-232 communication protocol and get the basic information of the laser.   

5.

 

SERVICE:

Provide  some  external  functions  for  customers.  See  4.4.1 

Interface Specification for details. 

6.

 

WATER

：

The pagoda typepipe connector. The intake and outlet are used 

for inflow and reflux cooling water. 

3                               

4                             

5                             

2                                 

1                               

6                           

Summary of Contents for RFL-P500H





























Reviews:

No comments