background image

武汉锐科光纤激光技术股份有限公司

WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD.

3

WARNING: You must use appropriate laser safety eyewear when operating

this device. The laser safety eyewear is selected according to the

range of wavelengths emitted from this product. The end user must

ensure that the laser safety eyewear used protects against light

emitted by the device over its entire range of wavelengths. Please

check the safety labeling on the product and verify that the personal

protective equipment (e.g. enclosures, viewing windows or view ports,

eyewear, etc.) being utilized is adequate for the output power and

wavelength ranges listed on the product.

1.3

Safety Labels

These include warning labels, apertures through which laser radiation

is emitted and labels of certification and identification, etc.

Specifications of these labels are as follows:

1

Laser Radiation Hazard

2: Aperture Label

3: Aperture Label(CN)

4: Class 4 Laser Product(EN) 5: Class 4 Laser Product(CN)

6:Class 2M Laser Product

Label for Guide Laser(EN)

7: Class 2M Laser Product

Label for Guide Laser(CN)

8: Electrical Hazard Label

9:Identification Plate

Summary of Contents for RFL-A2005





















Reviews: