background image

21

PROCEDURE TO CHECK CABLE:

PROCEDURE TO CHECK CABLE:

PROCEDURE TO CHECK CABLE:

PROCEDURE TO CHECK CABLE:

PROCEDURE TO CHECK CABLE:

1)

1)

1)

1)

1)

Enter a METER CAL number of one (1) in key labelled

2)

2)

2)

2)

2)

Depress key labelled

3)

3)

3)

3)

3)

Place BOOM switches to ON.

4)

4)

4)

4)

4)

With small jumper wire (or paper clip), short between the 2 o’clock and 6 o’clock

sockets with a "short-no short" motion.  Each time a contact is made, the TOTAL

VOLUME should increase by increments of 1 or more counts.

5)

5)

5)

5)

5)

If TOTAL VOLUME does not increase, remove the section of cable and repeat test

at connector next closest to Console.  Replace defective cable as required.

6)

6)

6)

6)

6)

Perform above voltage checks.

7)

7)

7)

7)

7)

If all cables test good, replace Flow Meter or Encoder.

NOTE:

NOTE:

NOTE:

NOTE:

NOTE: After testing is complete, re-enter correct METER CAL numbers before

application.

APPENDIX 2

PROCEDURE TO TEST FLOW METER/ENCODER CABLES

Disconnect cable from Flow Sensor.  Hold Flow Sensor cable so that the keyway is

pointing in the 12 o’clock position:

PIN DESIGNATIONS

PIN DESIGNATIONS

PIN DESIGNATIONS

PIN DESIGNATIONS

PIN DESIGNATIONS

2 o’clock socket location is ground.

10 o’clock socket location is power.

6 o’clock socket location is signal.

VOLTAGE READINGS

VOLTAGE READINGS

VOLTAGE READINGS

VOLTAGE READINGS

VOLTAGE READINGS

1) 2 o’clock socket to 6 o’clock socket = +5 VDC.

2) 2 o’clock socket to 10 o’clock socket = +5 VDC.

If a +5 VDC voltage reading is not present, disconnect

the Speed Sensor cable.  If the Flow reading is

restored, Test the Speed Sensor cable per Appendix

"PROCEDURE TO TEST SPEED SENSOR EXTENSION CABLES".

Summary of Contents for DCS 300




























Reviews: