Page 10
16. Flueing
Each 55 Built-in-Heater Flue Kit
(non-Chimney installation) contains:-
This flue kit may be used in new or existing
timber
chimneys
. The overall height of the flue is 3.6m.
Kit is supplied in a carton.
Note:
The Davin 55 Built-in-Heater Flue Kit
(non-Chimney) complies with AS/NZS
2918:2001 as per Applied Research Test
Report 05/1185, dated 15 September 2005.
All fires must be installed by a qualified
installer as per the manufacturer’s
instructions and AS/NZS2918:2001.
600mm from
roof
penetration
110mm minimum
clearance if lined
flue
150mm
(minimum)
Part No.
Description
Quantity
1
Galvanised outer liner
Ø100mm x 900mm long
4
2
Stainless steel inner liner
Ø75mm x 900mm long
4
5
Inner/outer flue liner spacer
4
8
Rain cap 75mm
1
9
Rain cap 100mm
1
702
Support Angle 950mm Long
2
55
Ecoteck Sara & Camino - new home
(non-Chimney installation)
Each 54:1 Built-in-Heater Flue Kit
(Chimney installation) contains:-
This flue kit may be used in new or existing
timber
chimneys
. The overall height of the flue is 3.6m.
Kit is supplied in a carton.
Note:
The Davin 54:1 Built-in-Heater Flue Kit
(Chimney) complies with AS/NZS
2918:2001 as per Applied Research Test
Report 05/1185, dated 15 September 2005.
All fires must be installed by a qualified
installer as per the manufacturer’s
instructions and AS/NZS2918:2001.
Part No.
Description
Quantity
1
Galvanised outer liner
Ø100mm x 900mm long
4
2
Stainless steel inner liner
Ø75mm x 900mm long
4
5
Inner/outer flue liner spacer
2
8
Rain cap 75mm
1
9
Rain cap 100mm
1
10
Telescopic offset 75mm (Stainless)
(2 x 45° bends)
2
11
Telescopic offset 100mm (Galvanised)
(2 x 45° bends)
2
702
Support Angle 950mm Long
2
54:1
Ecoteck Sara & Camino - new home
(Chimney installation)
Heat-resistant
floor protector
Seismic restraint
(to be fitted)
Chimney to
be flashed
by builder
150mm
(minimum)
Chimney cover
– optional extra
NOTE: Sara must be installed on an approved, raised-stand, while Sara can be installed lower to the fl oor with an optional
45mm base.
Each 52 Insert Flue Kit contains:-
y
t
i
t
n
a
u
Q
n
o
i
t
p
i
r
c
s
e
D
o
N
t
r
a
P
Stainless steel inner liner
ø75mm x 900mm long
Rain cap 75mm
T-adaptor/cleanout – ø75mm
Clamp – flexible flue to
stainless flue pipe
Flexible flue pipe – stainless
steel ø75mm x 1m
Bracket 75mm securing
flue pipe to wall
Casing cover – standard
ø75mm - ø300mm
Chimney cover – may be required
as an optional extra
This flue kit may be used in replacement applications in
masonry chimneys
. The overall height of the flue is
4.5m. Kit is supplied in two cartons.
Chimney cover
– optional extra
150mm
(minimum)
5
1
1
1
1
1
1
2
8
12
16
19
21
839
34
Heat-resistant
floor protector
Seismic Restraint
(to be fitted)
Note: The Davin 52 Insert Flue Kit complies
with AS/NZS 2918:2001 as per Applied
Research Test Report 05/1185, dated 15
Sepember 2005.
All fires must be installed by a qualified
installer as per the manufacturer’s instructions
and AS/NZS 2918:2001.
52
Ecoteck Sara - insert standard flue kit
