Safety Instructions
Assembly and Electrical Connection
- The power source is designed in accordance with the requirements for Class 1 appliance and must be
connected accordingly.
The system power supply may be connected only after a full connection and fixing of the cover, otherwise
there is a risk of an electrical shock.
Before drilling in the ceiling or in the walls, make sure that there are no distributions of electricity, gas or
water under the surface .
-
Choose the suitable positioning with respect to the accessibility for the
assembly and inspection, if possible at the points of the removable lower ceiling.
- For the maintenance and servicing needs, it must be possible to disconnect the device from the power supply.
For this purpose, it is possible to use a separate double-pole disconnection element or as applicable the current
protector combined with the circuit breaker fulfilling the requirement for a double-pole disconnection.
- The control unit has a cable of 1.5m legnth on the outlet, designed for the connection with the power supply
source. Also, 2 cables of 2.0m are taken out of the control unit for the connection of loudspeakers and the cable
of the aerial of the length of 2.5 m.
- For the positioning of the individual parts, it is recommended to prepare in advance a simple project or a graphic
design, which serves simultaneously for the material breakdown and the purchase of parts.
- The central light is positioned to the center of the ceiling, closer to the mirror. If you read in your bathtub, it is
suitable to direct the spot lights to this space. They may also be directed to the washbowl or to other places,
which we want to highlight in the bathroom, for instance the relief on the tiling etc..
- The cover of the ventilator should be positioned near the fixed ventilator or the ventilation hole.
- The elements are mounted in the holes in the lower ceiling of the size 140 x 140 mm, where they are fixed by
a spring.
- From the view side, the cutout is covered in the lower ceiling by the frame. For the assembly and checking
purposes, the lights and other parts are removable from the outer side of the lower ceiling.
- For the controller choose first the most suitable place, which will suit perfectly you and other users. In the
bathroom, the best positioning is on the wall above the bathtub reachable from a lying position.
For the bathroom cleaning, it should be however at least 15 cm above the bathtub rim. In WC, the controller is
positioned within the reach of a sitting person. It is recommended that the loudspeaker with the IR sensor be
directly visible together with the remote controller, but not always the site design allows this. It is possible to
achieve a smooth transmission of the control IR signals also by the natural reflections without a direct visibility.
However, it is necessary to verify the full functionality of the system prior to the final assembly of the components.
In the rear part of the remote controller, there are two strong magnets built in, through which the controller will
attach to the metal plate. The metal plate may be screwed to the wall, or attached by double-side sticking plate to
the wall tiles and so on. If fixing more plates, it is possible to move the controller to several places. The controller
may also be attached directly by the double-side sticking tape. This way of design however causes
complications upon replacement of batteries.
- Based on the project design, measure on the lower ceiling the places of mounting the individual lights,
loudspeakers and other accessories.
- Cut out holes in the lower ceiling - 140 x 140 mm.
- In the space between the ceilings, mount the control unit and the power source.
-
The batteries used in the remote controller must not be exposed to excessive heat, for instance to solar
radiation, fire and likewise
The product may be used only for the purposes described below.
- Upon the installation and operation, all applicable valid standards and regulations must be complied with.
- The device may be assembled and put to operation only by the person with the respective electrotechnical
qualifications
Positioning of the Lights and Cover of the Ventilator:
Positioning of the Remote Controller and Loudspeaker:
Assembly Process:
All system elements must be covered by an inflammable, ventilated soffit. Any elements above the level of the
soffit must not be exposed to a dripping or splashing water. From the view side, the resistance against water is
determined by the level of coverage (IP xx) of the given element.
-
.
-
.
The control unit and the power supply are fixed to the ceiling above the soffit, or as the case may be to the
supporting structure of the soffit.
- 13 -
Summary of Contents for RC1-L1
