background image

Installation

FCC Requirements

Rauland-Borg’s Model TC4171  (COA Module) conforms to the requirements of the Federal Communica-
tion Commission’s Rules and Regulations, Part 68, which governs the connection of circuitry to protect
the telephone network. The user must be aware of the requirements pertaining to the installation and
the operation of this protective device. The rules are summarized below; the complete current rules will
be in the current copy of the FCC’s Rules. All of the pertinent rules must be followed.

1. The TC4171 (COA) should only be connected to a standard subscriber line via the proper

coupler installed by the telephone company; it should never be connected to a party line or
coin line.

2.

You must give the local telephone company:

a. notice that you want to install an FCC-approved device to their line (similar notice is

required of a final disconnect.)

b. the registration number and the ringer equivalence, which are marked on the

compliance label, and

C. 

the connection required for the TC4 171 (COA) - the RJ2  1X, RJ 1 lC, or RJ 11W (see this
manual, KI-1583, the Interconnect Planning Manual, KI-1582 and wiring diagrams
KM-0714 and KM-0716).

3. Once the telephone company has installed the proper connector, insert the plug coming from

the TC4 171 (COA) wire-wrap terminals.

4. No repairs may be made to the TC4171 (COA) or to the TC4001  (main central assembly) while

the TC4171 is connected  to the phone line. If any malfunction occurs on this interconnect
device or with the TC4001,  disconnect the TC4171 and replace it with a unit known to be
operating. If the Telecenter equipment is adjudged to be operating properly but the problem
still exists, contact the telephone company. Reconnect the phone system only after determining
that this equipment is not the source of the malfunction.

5. If the TC4171 (CGA) should cause harm to the telephone network, the telephone company is

required, where practicable, to notify you that temporary discontinuance of service may be
required. If advance notice is not practicable, the telephone company is permitted to discon-
tinue its service immediately, provided that such an action is reasonable under the circum-
stances In the case of temporary discontinuance, the telephone company is required to:

a. Promptly notify you of the temporary discontinuance.

b. Give you the opportunity to correct the situation that caused the discontinuance

C. 

Inform you of your rights to bring a complaint to the FCC pursuant to the procedures set
forth in that agency’s Rules. Copies of the procedure for making a complaint can be
obtained from Rauland-Borg.

6. The telephone company can make changes in its facility, operations, equipment, or procedures,

provided that the changes are reasonably required and are consistent with the FCC’s regulations.
If these changes render the customer’s equipment incompatible or require that it be modifed, the
telephone company is required to give sufficient advance notice in writing to allow the customer
the opportunity to maintain uninterrupted service.

7. Do not modify, repair, or alter this registered interconnect device, the TC4171  (COA): any such

actions will void the warranty and could result in discontinuance of service from the telephone
company. If the TC4171 requires service, return it to the Rauland-Borg Corporation.

Page 2 of 20 ©

 1989 Rauland-Borg 

Corporation

 (Orig.  10/88; Rev. 

1/89)

Summary of Contents for Telecenter IV





















Reviews:

Related manuals for Telecenter IV