Rauch QUANTRON-A AXIS-M 20 EMC Instruction Manual Download Page 99

Page: 99 / 116

Spreading operation with the QUANTRON-A control unit

5.5

Spreading in the MAN km/h operating mode

If there is no forward speed signal, the MAN km/h operating mode is active.

Switch on the QUANTRON-A control unit.

Open the

Machine settings > AUTO/MAN mode

menu.

Select

MAN km/h

in the menu.

Enter the forward speed.

Press

Configure the fertiliser settings:



Application rate (kg/ha)



Working width (m)

Insert fertiliser.

Carry out a calibration to determine the flow factor
or
Obtain the flow factor from the fertiliser chart.

Enter the flow factor manually.

10.

Press the

Start/Stop

key.



The spreading starts.

NOTICE

In order to achieve an optimum spreading result in the MAN km/h operating
mode, a calibration is to be carried out before starting the spreading.

NOTICE

Always observe the set speed during spreading.

Summary of Contents for QUANTRON-A AXIS-M 20 EMC





















































































































Search results

Summary of Contents for QUANTRON-A AXIS-M 20 EMC

Reviews:

Related manuals for QUANTRON-A AXIS-M 20 EMC

Brands by name

Popular brands

Rauch QUANTRON-A AXIS-M 20 EMC, Instruction Manual

Search results

Summary of Contents for QUANTRON-A AXIS-M 20 EMC

Reviews:

Related manuals for QUANTRON-A AXIS-M 20 EMC

Brands by name

Popular brands