Rattler 200 Installation Manual Download

Page: 4 / 27

primary harness (H1), 12-pin connector

The primary harness is the standard 12-pin harness used by DEI security systems. Two pins in the harness do not

have wires (H1/5 and H1/7). The functions of all the wires that are used in the primary harness are outlined in

this section. The wire connections are described in the

Primary Harness (H1) Wire Connection Guide

section.

______

relay harness (H2), 6-pin connector

______

*NOTE:

VIOLET and VIOLET/BLACK are common at the fuse holder.

VIOLET*

UNLOCK #87 NORMALLY OPEN (INPUT)

BLUE/BLACK

UNLOCK #30 COMMON (OUTPUT)

BROWN/BLACK

UNLOCK #87A NORMALLY CLOSED

VIOLET/BLACK*

LOCK #87 NORMALLY OPEN (INPUT)

GREEN/BLACK

LOCK #30 COMMON (OUTPUT)

WHITE/BLACK

LOCK #87A NORMALLY CLOSED

H2/A

H2/B

H2/C

H2/D

H2/E

H2/F

RED/WHITE

(-) 200 mA CHANNEL 2 VALIDITY OUTPUT

RED

(+)12V CONSTANT POWER INPUT

BROWN

(-) HORN HONK OUTPUT

YELLOW

(+) SWITCHED IGNITION INPUT

BLACK

(-) CHASSIS GROUND INPUT

BLUE

(-) 200 mA SECOND UNLOCK OUTPUT

BLACK/WHITE

(-) 200 mA DOMELIGHT SUPERVISION OUTPUT

WHITE/BLUE

(-) 200 mA CHANNEL 3 VALIDITY OUTPUT

WHITE

(+) LIGHT FLASH OUTPUT

ORANGE

(-) 500 mA GROUND-WHEN-ARMED OUTPUT

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

Summary of Contents for 200




























Search results

Summary of Contents for 200

Reviews:

Related manuals for 200

Brands by name

Popular brands

Rattler 200, Installation Manual

Search results

Summary of Contents for 200

Reviews:

Related manuals for 200

Brands by name

Popular brands