Rattler 200 Installation Manual Download

Page: 23 / 27

Release.

Once the code is learned, the Valet/Program switch can be released.

You can advance from one channel to another by releasing the Valet

/Program switch and tapping it to advance

channels and then holding it. For instance: You have programmed Channel 1 and you want to program Channel

2. Release the Valet

/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2.

Now, press and

HOLD

the Valet/Program switch down and the unit will chirp twice. As before, do not release it.

If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice

and then release it to advance to Channel 3. Then press the Valet/Program switch once more and

HOLD

it. The

horn will honk three times to confirm it is ready to receive the code from the transmitter to program Channel 3.

The learn routine will be exited if:

■

The ignition is turned off.

■

The Valet/Program switch is pressed too many times.

■

More than 15 seconds elapses between steps.

One long horn honk (if connected) indicates that the Learn Routine has been exited.

transmitter configuration

The transmitters can be programmed with the Standard Configuration by using the Channel 4 Auto Learn Standard

Configuration function in the Transmitter/Receiver Learn Routine. When programmed for Standard Configuration,

the transmitter buttons are assigned to the following functions:

Button I (III*) ......................................operates ........................................Arm/Panic

Button II (IV*) ......................................operates ........................................Disarm/Channel Two

Buttons I and II (III and IV*)..................operate..........................................Channel Three

*NOTE:

If using an optional four-button remote, the Standard Configuration may alternately

be taught to Buttons III and IV by pressing Button III in Step 3 of the Transmitter/Receiver
Learn Routine.

to exit learn routine

to advance from one channel to another

Summary of Contents for 200




























Search results

Summary of Contents for 200

Reviews:

Related manuals for 200

Brands by name

Popular brands

Rattler 200, Installation Manual

Search results

Summary of Contents for 200

Reviews:

Related manuals for 200

Brands by name

Popular brands