background image

Page 9

Page 8

Option 2:

 Program the SmartRescue to Allow the Emergency Phones to call the SmartRescue First, then Outside 

Number(s)

1. 

Leave SmartRescue handset hung up

2. 

Hold down red Disconnect and Sub-Master 1 buttons for 5 seconds

3. 

Release buttons (you will hear a confirmation tone)

4. 

Press Phone 2 button, then red button, then the Phone 1 button

5. 

Press Sub-Master 2 button, then Sub-Master 1 button (you will hear a confirmation tone)

**Used when staff is available to answer calls.

Step 9: Programming the Emergency Phone(s)

Option 1:

 Call Emergency Numbers Offsite without Stopping at the SmartRescue

 

     1.

 Press 

Enter

 to get into program mode

 

     

2.

 Press 

1, Enter, (Emergency Number), Stop

 

     3.

 If using 2 emergency numbers, press 

2, Enter, (Emergency Number), Stop

 

     4.

 Repeat for up to 5 total emergency numbers

 

     

5.

 To exit program mode, press and hold 

Stop 

for 2-3 seconds until warble sound

Option 2: 

Call SmartRescue First, if No Answer Call Emergency Numbers Offsite

 

     1.

 Press 

Enter

 to get into program mode

 

     

2.

 Press 

1, Enter, (Emergency Number), Stop

 

     3.

 Press 

2, Enter, 

(same 

Emergency Number

 as entered in b), 

Stop

 

     

4.

To exit program mode, press and hold 

Stop 

for 2-3 seconds until warble sound

Program the Location Message:

Note: 

This is always done, unless your Call Center requests it not to be.

 

     1.

 Press 

Enter

 to get into program mode

 

     

2.

 To turn on message, press 

1, 3, Enter, 2

 

 

a. For no message, press 

1, 3, Enter, 0

 

     3.

 Press 

6, Record, 

(wait for beep, speak your message), 

Stop

 

     

4.

 To program frequency of message, press 

1, 3, Enter, ___

 

 

1 = Plays message once

 

 

2 = Plays message twice (this is standard configuration)

 

 

3 = Plays message until the called party presses 

*

 on their phone

 

     

5.

 To exit program mode, press and hold 

Stop 

for 2-3 seconds until warble sound

**

The Elevator Industry 

REQUIRES

 the ability to call into each elevator from outside of the 

building. For instructions on how to put each phone into Consolidator Mode, see page 11.

Operations & Testing the System

Step 10: Operating and Testing the System 

1. Once all connections are made, the following LEDs should be lit:

 

• Power LED, located on bottom edge of the face plate, will be constantly lit green.

 

• Battery LED, located on bottom edge of the face plate, will be constantly lit:

 

 

•  Red = Low level charge

 

 

•  Yellow = Mid level charge

 

 

•  Green = Full charge

Note: 

Battery may take up to 18 hours to fully charge.

Summary of Contents for 2500-205D
















Reviews: