background image

6

TROUBLESHOOTING

Water not being drawn in 

• Check Ball Stuck

 

Shutoff seacock and remove intake hose

 

Using an eraser end of pencil be sure check ball is  

 

moving freely

• Debris lodged in intake valve body

 

Check and clean valve body

• Piston O-ring worn

 

Replace Piston O-ring

• Inlet valve in wrong position

 

Inlet valve should only rotate 1/4 turn

Leak around piston shaft

• Cartridge seal worn

 

Replace cartridge seal

 

Inspect and replace piston shaft if scored

Water accumulates in the bowl too fast

• Flapper valve not seated properly

 

Close intake valve and pump dry - clean or repalce  

 

flapper valve as necessary

• Joker valve not closing or opening properly

 

Clog or restriction in discharge line

 

Close intake valve and pump dry - clean or replace  

 

joker valve as necessary

Not enough water to rinse bowl

• Intake valve positioned improperly

 

Be sure inlet knob only turns 1/4 see fig. #3

• Debris around intake or discharge check balls

 

Remove check balls, clean and replace as necessary

• Scored pump housing or worn piston "O" ring

 

Inspect inside of housing replace "O" ring and  

 

housing as necessary

• Intake line or strainer clogged

 

Clean line and strainer

Water rises in bowl 

• Vented loop(s) not breaking siphon

 

Close discharge seacock, then intake seacock to  

 

determine which is causing the problem.  Clean or  

 

replace vented loop(s) parts. 

• Joker valve worn

               

Inspect, clean or replace as needed

Odor comes from head area when flushed

• Marine vegetation lodged in bowl

 

Remove bowl and attach pressure water at spud assy.

 

Install strainer in intake line

• Intake water is foul (most common in salt and brackish)

 

Install Knocks Out Odors Kit (KO2) to help deodorize    

 

intake water

• Back pressure from holding tank

 

Tank full or vent clogged, inspect and clean

• Permeated discharge hose

 

rub with warm damp rag if smell transfers to rag  

 

 

replace hose (Saniflex (SFH) recommended).

RARITAN INSTALLATION ACCESSORIES

Part No. 

Description

163000 

In-Line Strainer

164000BR 

Push button switch

1PCP22 

C.P., Cleans Potties, Bio-enzymatic, 22 oz.

CHTII 

Compact holding tank - 5 gallon

SFH 

Sani-Flex Hose 

SL1CC 

Super Lube 1cc tube

KO2 

Knocks Out Odor Kit

TD90319 

Vented Loop 3/4"  

TD90323 

Vented Loop 1 1/2" 

TD90314W 

"Y" Valve

BOWL & SEAT

Part No. 

Description

16  1236AW 

Spud assy.

1   1237W 

Marine-size Bowl assy.

1     1244W 

White Household-style Bowl assy.

7  25105 

Bowl Gasket

2  1238SC 

Marine-size seat & cover; Slow Close

2  1245SC 

Household-style seat & cover; Slow 

Close

11  VCAP 

Vinyl Cap

OVERHAUL KITS

Part No. 

Description

PHRKIIC 

PHII&PHEII-Cartridge Seal

PHIIPUMP 

PHII Pump replacement assembly

ADDITIONAL PARTS FOR RARITAN PH SUPERFLUSH

L563  0316kgs

Summary of Contents for PH Superflush









Reviews: