background image

 

ATTACHMENT-2 

GISAN WARRANTIES 

 

Gisan Standard RAN Pump Warranty 
Gisan  warrants all equipment manufactured by Gisan and  bearing  its name to be free from defects in material and 
workmanship  on  the  date  of  sale  to the  original  purchaser  for  use. With the  exception  of  any  special,  extended, or 
limited warranty published by Gisan, Gisan will, for a period of five years from the date of sale, repair or replace any 
part  of  the  equipment  determined  by  Gisan  to  be  defective.  This  warranty  applies  only  when  the  equipment  is 
installed, operated and maintained in accordance with Gisan’s written recommendations. 
 
This warranty does not cover, and Gisan shall not be liable for general wear and tear, or any malfunction, damage or 
wear  caused  by  faulty  installation,  misapplication,  abrasion,  corrosion,  inadequate  or  improper  maintenance, 
negligence, accident, tampering, or substitution of non-Gisan component parts. Nor does this warranty cover moving 
consumable  pump  parts  such  as  diaphragms,  balls,  ball  seats,  o-rings  and  valves.  Nor  shall  Gisan  be  liable  for 
malfunction,  damage  or  wear  caused  by  the  incompatibility  of  Gisan  equipment  with  structures,  accessories, 
equipment  or  materials  not  supplied  by  Gisan,  or  the  improper  design,  manufacture,  installation,  operation  or 
maintenance of structures, accessories, equipment or materials not supplied by Gisan. 
 
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Gisan 
distributor  for  verification  of  the  claimed  defect.  If  the  claimed  defect  is  verified,  Gisan  will  repair  or  replace  free  of 
charge  any  defective  parts.  The  equipment  will  be  returned  to  the  original  purchaser  transportation  prepaid.  The 
pump must be fully cleaned internally and externally and correctly packaged according to instruction manual. A dirty 
or  improperly  packed  pump  will  not  be  accepted  by  Maintenance  Dept.  If  inspection  of  the  equipment  does  not 
disclose  any  defect  in  material  or  workmanship,  repairs  will  be  made  at  a  reasonable  charge,  which  charges  may 
include the costs of parts, labor, and transportation. 
 
Gisan’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer 
agrees  that no  other  remedy  (including, but not  limited  to,  incidental  or  consequential  damages  for  lost  profits,  lost 
sales,  injury  to  person  or  property,  or  any  other  incidental  or  consequential  loss)  shall  be  available.  Any  action  for 
breach of warranty must be brought within five years of the date of sale. Gisan makes no warranty, and disclaims all 
implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, 
materials  or  components  sold  but  not  manufactured  by  Gisan.  These  items  sold,  but  not  manufactured  by  Gisan 
(such as electronic control systems, sensors etc.), are subject to the warranty, if any, of their manufacturer. Gisan will 
provide purchaser with reasonable assistance in making any claim for breach of these warranties. 
 
Extended Product Warranty 
Gisan  warrants  all  RAN  Pump  air  valve  center  sections  to  be  free  from  defects  in  material  and  workmanship  for  a 
period of five years from date installed in service by the original purchaser. Normal wear of items such as packings 
are not considered to be defects in material and workmanship. 
 
Five years Gisan will provide spare parts and labor. 
Five to ten years Gisan will replace defective parts only. 
 
All written and visual data contained in this document reflects the latest product information available at the time of 
publication. Gisan reserves the right to make changes at any time without notice 
 

Gisan Information 

If  you  need  further  information  please  contact  Gisan  distributor  in  your  country  or  call  this  number  to  identify  the 
distributor closest to you. 
 
 
 

 
 

Gisan Makine San. Tic. Ltd. Şti. 

Birlik Sanayi Sitesi 3. Cadde No: 83  Beylikdüzü İstanbul Turkey 

Tel.  : 00 90 212 875 03 17 (pbx) 

Fax: 00 90 212 875 03 18 

E-mail / Web : 

[email protected] / www.ranpump

 

 
 

 
 

 

 

Summary of Contents for B15-AX

























Reviews: