background image

TF2014501-BA English                                                  Page 17 of 18                                                                  20190107 V.1 

LIMITED WARRANTY 

1.  Manufacturer  warrants  this  Product  to  be  free  from  defects  in  workmanship 

and  materials  for  a  period  of  Ninety  (90)  days  from  the  date  of  purchase, 
PROVIDED claims are submitted, in writing, with proof of purchase. 

2.  If  any  part  of  this  item  fails  because  of  a  manufacturing  defect  within  the 

Limited Warranty  Period,  Manufacturer  offers  to replace  such  part(s)  provide 
that such parts have not been improperly repaired, altered, or tampered with or 
subject  to  misuse,  abuse  or  exposed  to  corrosive  conditions.  This  Limited 
Warranty is, however, subject to certain limitations, exclusions, time limits and 
exceptions (Hereinafter “Conditions”) as listed below. Read these Conditions 
carefully. 

3.  This  Limited  Warranty  shall  be  limited  to  the  replacement  or  repair  of  any 

part(s) which Manufacturer determines, after reasonable examination, to have 
been defective at the time of manufacturing and manufacturer’s obligation(s) 
shall  be  limited  to  replacement,  if  any,  of  defective  part(s)  which  shall  be 
shipped  at  Original  Purchaser’s  expense  to  Original  Purchaser’s  designated 
shipping address. 

4.  This  Limited  Warranty  is  given  to  and  covers  the 

ORIGINAL  PURCHASER 

ONLY 

and  such  coverage  terminates  Ninety  (90)  days  from  the  date  of 

purchase.

 

5. 

DAMAGE LIMITATION WARNING: 

IN NO EVENT SHALL MANUFACTURER 

BE LIABLE FOR ANY INCIDENTIAL OR CONSEQUENTIAL DAMAGES, 
INCLUDING (BUT NOT LIMITED TO) LOSS OF USE OF THE PRODUCT, 
LOSS OF TIME, INCONVENIENCE, EXPENSES FOR TRAVEL, 
TRANSPORTATION LODGING EXPENSES, LOSS BY DAMAGE TO 
PERSONAL PROPERTY OR LOSS OF INCOME, PROFITS OR REVENUE. 

6. 

MANUFACTURER’S OBLIGATION:

 Manufacturer

’s liability shall be limited to 

the delivery of a good, merchantable Product and, if necessary, the repair or 
replacement, at manufacturer’s option, of any defective part or unit. 

7. 

TRANSFER  LIMITATIONS:

  This  Limited  Warranty  is  not  assignable  or 

transferable. It covers only the original purchaser. 

8. 

RESERVED  RIGHT  TO  CHANGE:

  Manufacturer  reserves  the  right  to  make 

changes  or  improvements  to  products  it  produces  in  the  future  without 
imposing  on  itself  any  obligations  to  install  the  same  improvements  in  the 
products it has previously manufactured. 

9.  This  Limited  Warranty  gives  the  Original  Purchaser  specific  legal  rights  but 

there may be other rights which vary by jurisdiction. 

10.  This warranty does not cover the following items: 

 

Chips or scratches on porcelain or painted surfaces. 

 

Rust or corrosion is not deemed a manufacturing or materials defect. 

 

Discoloration or loss of paint due to handling during assembly, heat or 
cleaning products. Paint may require touch up. 

 

Stainless steel discoloration or corrosion. 

 

Consumables such as batteries. 

Summary of Contents for TF2014501-BA



















Reviews: