background image

Manual-8

©Rane Corporation  10802 47th Ave. W.,  Mukilteo WA 98275-5000  TEL 425-355-6000  FAX 425-347-7757  WEB rane.com

Power

This IEC320-C5 power jack receives the power cable shipped 

with the unit. 

MP 2016S Mixer Port

This is the required socket to connect the XP 2016S to the MP 

2016S, using the ribbon cable supplied with the XP 2016S. If 

a ribbon longer that that supplied with the XP 2016S is used, 

crosstalk may increase, and immunity to RF, magnetic and con-

ducted interference may be compromised.

XP 2016S Ribbon Connections: (PIN 1 marked Ñ)

1) GND

2) GND

3)  MIX RIGHT OUT

4)  MIX LEFT OUT

5) GND

6)  METER LEFT IN

7)  METER RIGHT IN

8) GND

9)  CH 6R IN

10)  CH 6L IN

11) GND

12)  CH 5R IN

13)  CH 5L IN

14) GND

15)  CH 4R IN

16)  CH 4L IN

17) GND

18)  CH 3R IN

19)  CH 3L IN

20) GND

21)  CH 2R IN

22)  CH 2L IN

23)  XP 2016 ENABLE (GND)

24)  CH 1R IN

25)  CH 1L IN

26) GND

Fader Cleaning

With heavy use in harsh environments, the faders may need 

lubrication. This treatment extends longevity and can make used 

faders as good as new. The fader assembly must be removed from 

the XP 2016S for proper cleaning. We recommend:

Caig DeoxIT® Fader F-series spray lubricant

Order it from:

CAIG Laboratories, Inc.

12200 Thatcher Ct.

Poway, CA  92064

Phone 800-CAIG-123

Email 

[email protected]

Web 

www.caig.com

CLEANING INSTRUCTIONS

A. Fader assembly removal

1. Remove (2) 3mm screws.

2. Draw fader assembly out through hole.

3. Remove ribbon cable.

B. Fader cleaning

1. Hold the fader assembly away from the mixer.

2. Position the fader at mid-travel.

3. Spray cleaner/lubricant into both ends of the fader.

4. Move the fader over its full travel back and forth a few times.

5. Shake excess fluid from the fader assembly.

6. Wipe off excess fluid.

At this point the control should be operational. If fader perfor-

mance is questionable then replacement of the pot is the only 

sure remedy. The fader is available to purchase online in the Rane 

Factory Store at 

rane.com

. You may also call the Rane factory 

if you are in the USA, or call your distributor outside the USA 

(

rane.com/internat.html

).

MP 2016S

MIXER

ACN 001 345 482

U.S. PATENT 7,043,032

MADE IN U.S.A.

RANE CORP.

XP 2016S

COMMERCIAL AUDIO

EQUIPMENT 24TJ

R

100-240 V

50/60 Hz 12 WATTS

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is 

subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.

DOC 111041

Summary of Contents for XP 2016S











Reviews: