Manual-
CP 64S REAR PANEL
1
PAGING INPUT
Euroblock connectors may be operated balanced or unbalanced. See CP 64S Connections on page Manual-3.
2
PAGE 1 and PAGE 2 INPUT MIC / LINE
switches select 30 dB Input Pads when set to LINE.
Phantom Power (if enabled) is
disabled when LINE is selected. See page Manual-4 to internally set Phantom Power.
PAGE 1 and PAGE 2 INPUT TRIM
controls adjust Page Input preamplifier gain to match the microphone/source in use,
not
to
set the page level in the Zones. The range is 30 dB to 60 dB.
PAGING INPUTS OL
indicator lights when either of the Page Input preamplifiers comes within 3 dB of clipping, assisting the
setting of these trims.
3
Four
PROGRAM INPUTS
are provided. Three are non-priority Inputs. The fourth is a Program PRIORITY Input. When signal
is present at the PRIORITY Input, it is
automatically
selected as the Input source in the Zone(s) it is assigned with the Program
PRIORITY ASSIGN ZONE switch.
4
PRIORITY ASSIGN ZONE
switch determines in which Zone(s) the automatic priority override is enabled.
Off
(none),
Zone 1
,
Zone 2
or
Both
are the possible settings. If you do not intend to use the Priority Input as an
automatic override
Input, do
not
assign
it with this switch. Use the Zone PROGRAM SELECT switch on the front panel.
5
LIMITER
threshold controls set the maximum output level for each Zone. These circuits are true voltage limiters with a ratio of
15:1. The threshold range is -20 dBu to +20 dBu.
6
OUTPUTS
feature balanced cross-coupled line drivers with a Euroblock connector for each Zone. Zone 1 is stereo. Zone 2 is
mono, and both Expand outputs are mono.
When operating cross-coupled line drivers unbalanced, it is
essential
to ground the (–)
pin.
See CP 64S Connections on page Manual-3.
7
ZONE EXPAND OUT
switches assign
Page
-only,
Program
-only or
Zone 1 or Zone 2
as the source for each Expand Output.
8
DETECT THRESHOLD
sets the Paging input signal level required to gate a Page
on
and light the front panel ACTIVE
indicator. The range is -∞ (on) to +4 dBu.
9
REMOTE PAGE ZONE ASSIGN
port provides the interface for the PR 2 wired remote. The PR 2 remote is used for Zone as-
signment of Page Inputs. Follow the wiring as described on page Manual-5.
0
REMOTES
ports provides the wiring interface for two optional ZR 1 wired remotes. Each ZR 1 remote provides remote control
of Zone Level and Zone Program Select functions. Follow the wiring as described on page Manual-5.
q
Universal Voltage Input:
via a miniature IEC 60320 C6 appliance inlet. This mates with an IEC 60320 C5 line cord (USA
domestic). Do
not
lift the ground connection!
q
0
6
1
9
4
7
2
8
5
3
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30
+60
1&2
PRIORITY
3
2
1
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–
+
–
+
–
+
–
D1 D0
Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2
PAGE 1
LIMITER
WIRING
ZONE 1
ZONE 2
PAGE 1
TRIM
PAGE 2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30
+60
MIC
LINE
–20
+20
–20
+20
REMOTES
OUTPUTS
MIN
MAX
PROGRAM INPUTS
ZONE 2
EXPAND OUT
ZONE 1
EXPAND OUT
ZONE
2
Z2 PGM
Z2 EXPAND Z2 MONO
REMOTE 1
INPUT 1
REMOTE 2
INPUT 2
Z1 RIGHT
Z1 EXPAND
Z1 LEFT
Z2 LEVEL
Z1 PGM
Z1 LEVEL
ACN 001 345 482
MIC
LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM
PGM
PAGE
THIS DEVICE COMPLIES WITH
PART 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
