background image

RANDOM*SOURCE

 

RANDOMSOURCE.NET

4

J. HAIBLE Dual WASP Filter (Euro)

• 

There are 2 pairs of (optional) trimmers to optimize the MODE performance:  

TRIM X

” and “

TRIM Y

” control CV Rejection. These can be calibrated by ear (or scope). See details 

below.  

BIAS

” trimmers can be used to eliminate output offset, for this you need a good scope (a good DMM 

might work, too). This is really for the perfectionists - see calibration info below -, so if you don’t have a 
scope, it’s probably best not to bother: install RGX, RGY and a link from pin 1 to 2 (center) or 3. 

• 

Be careful: 2 of the op-amps (left and right) are SINGLE! The ones in the center row are DUAL.  

Do not confuse SINGLE and DUAL op-amps up or they will burn

• 

There’s a dual op-amp (in SMT) on the panel pcb: without this, turning the CV attenuator (without CV 
going in) will affect the Cutoff frequency. Install the op-amp to avoid this (but omit the resistors marked 
RLX!) 

• 

Recommenden: use OPA2134 (instead of TL072) for all dual op-amps and  
OPA134 for the single ones.

• 

The Dual WASP has to be powered by a 

+/-12V stabilized PSU

 only. 

• 

Random*Source has aquired all rights to Jürgen Haible’s electronic heritage and is the only legitimate 
source for Jürgen Haible’s designs. 

Summary of Contents for JHAIBLE Dual WASP Filter










Reviews: