Page
4
of
12
RAD0322PRO
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
FITTING INSTRUCTIONS
•
To fit R&G radiator guard to the bike, insert the 4x rubber grommets into the radiator guard in the
holes circled in yellow in
Fitting Diagram
if they do not come already installed & slide the R&G
Radiator Guard into position.
•
Remove both radiator cowls from the bike. To do this, remove the 2x button head bolts on each
side, as arrowed in
Picture 1
and then pull the panel away from the bike.
•
Repeat this process for the other side of the bike.
•
Remove the two bolts circled in
Picture 2
(one on each side).
•
Remove the 2x bolts that secures the top of the radiator to the frame, as shown in
Picture 3
.
•
To remove the radiator from its mounting lug on the right side of the bike, ensure the left side
mount is clear and gently slide the radiator off the frame mount.
•
Offer the R&G Radiator Guard into position and locate the upper tab on the right side over the
frame mount (as shown in
Picture 4
) before sliding the radiator back on.
•
The upper tab on the left side should now locate in position on the LHS. Refit the original bolt and
loosely tighten.
•
Secure the bottom of the radiator guard in place using 2x supplied R&G one way cable ties through
the holes circled in green in the
Assembly Diagram
, the locking part of the cable tie needs to be
secured from behind the radiator as shown in the
Picture 5
.
•
Re-fit all fairing panels & check all components are secure and all bolts are tight before riding.
ISSUE 1 – 12/07/2023 (MH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.
