Page
7
of
21
LP0308
R&G
Unit
1
, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)
1
420 89007 Fax: +44 (0)
1
420 87301 www.rg-racing.com Email: [email protected]
•
The R&G tail tidy can now be offered up to the mounting holes on the underside of the tail unit.
At this time route the cables through the hole where they were removed previously.
•
Insert the M6 bolts and secure the tail tidy in place while reattaching the support bracket shown
in
Picture 5
.
•
Tighten the 4 M6 screws with the M6 washers and the nuts which were removed from the
original license plate holder as shown in
Picture 5
.
•
Re-connect the illuminator and indicator wires, ensuring that the left and right sides are
connected correctly respectively.
•
The fuse bracket and seat catch mechanism plates can now be re-attached using the same bolts
removed in
Picture 3
.
•
Now the tail right-hand-side panel can be re-attached by first fastening the bolts shown in
Picture 2
, and then fastening the screws shown in
Picture 1
.
•
The seat can then be re-attached, ensuring that it positively clicks into place and is secured by
the locking mechanism.
•
The Rubber bung provided (Item 6) can be used to cover the seat key lock and keep it free
from dirt and water. Push it over the lock barrel and it will stay in place. Note that the key lock
can be operated with the rubber bung in place.
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON
THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE
HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE
ROAD. IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE
AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
ISSUE 1 - 02/07/2021 - (WW)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may
make design changes which do not diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has
been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits
the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on
the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its
option either supply a replacement or refund the purchase money but shall not be liable if the Products have been
modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to
R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential
loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or
service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned
direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned
to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to
a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of
purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless
within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
