R&G LP0158, Fitting Instructions Manual

Page: 5 / 17

R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 5

FIT TO THE INDICATOR MOUNTING BRACKET (ITEM 8) IN THE SAME
MANNER.
IF USING THE MINI INDICATORS

IF FITTING MINI-INDICATORS (R&G PRODUCT CODE RG370= BULB TYPE,
RG371= LED TYPE OR RG372= AERO LED TYPE), FIT THE INDICATORS OF
CHOICE (PLEASE USE THE SUPPLIED HEAT SHRINK (ITEM 11) TO PROTECT
THE WIRING) AS SHOWN IN PICTURE 7.

FIT THE INDICATOR MOUNTING BRACKET (ITEM 8) TO THE LICENCE PLATE
BRACKET (ITEM 2) USING TWO OF THE M6 BUTTON HEAD BOLTS (ITEM 4)
AND WASHERS (ITEM 5) AS SHOWN IN PICTURE 8.

FIT THE NEW LICENCE PLATE ILLUMINATOR (ITEM 7) TO THE NEW LICENCE
BRACKET (ITEM 2) AS SHOWN IN PICTURE 8 (PLEASE USE THE SUPPLIED
HEAT SHRINK (ITEM 11) TO PROTECT THE WIRING).

PLEASE NOTE YOU WILL NEED TO GLUE THE LIGHT SHROUD TO THE
LED LICENCE PLATE LIGHT BEFORE FITTING USING SUPER GLUE.

PLEASE USE THE PROVIDED CABLE CLIPS (ITEM 9) AND THE CABLE TIES
(ITEM 13) TO TIDY THE WIRING AS SHOWN IN PICTURE 8.

FIT THE LEFT (ITEM 1) AND RIGHT HAND SIDE (ITEM 3) SUPPORT BRACKETS
TO THE LICENCE PLATE BRACKET (ITEM 2) USING THE M6 BUTTON HEAD
BOLTS (ITEM 4) AND WASHERS (ITEM 5) AS SHOWN IN PICTURE 9,
DO NOT
FULLY TIGHTEN THE BOLTS AT THIS STAGE.

CUT AND APPLY THE SELF ADHESIVE FOAM (ITEM 12) AS SHOWN IN
PICTURE 10 TO HELP PREVENT MARKING OF THE REAR LIGHT.

OFFER THE NEW LICENCE PLATE BRACKET INTO POSITION AS SHOWN IN
PICTURE 11.

USING THE ORIGINAL BOLTS (AS SHOWN IN PICTURE 4) SECURE THE NEW
LICENCE PLATE BRACKET INTO POSITION AND TIGHTEN THE TWO BOLTS
ON THE SUPPORT BRACKETS.

FEED THE WIRES THROUGH THE RUBBER GROMMET AS ORIGINAL.

IF USING THE ORIGINAL INDICATORS, RECONNECT INDICATOR (TURN
SIGNAL) PLUG SOCKETS AS ORIGINAL.

IF USING R&G MINI INDICATORS USE THE SUPPLIED CONNECTORS (ITEM 6)
TO CONNECT THE INDICATORS.

THE ORIGINAL LICENCE PLATE ILLUMINATOR WIRING MAY BE CUT AND
SHUT IN ORDER TO REUSE THE ORIGINAL WIRING PLUG SOCKET FOR
CONNECTION OF THE R&G LICENCE PLATE ILLUMINATOR, TO DO THIS WE
SUGGEST CUTTING THE CONNECTOR FROM THE ORIGINAL LICENCE PLATE
ILLUMINATOR WIRING AND FIT THE SUPPLIED BULLET CONNECTORS TO
EACH WIRE, ALLOWING THE CONNECTION OF THE R&G LICENCE PLATE
ILLUMINATOR TO THE ORIGINAL PLUG SOCKET. PLEASE CHECK THE
OPERATION OF THE LIGHT (IF ILLUMINATION FAILS, SWOP THE BULLET
CONNECTORS OVER) THIS CONNECTION MAY ALSO BE SOLDERED.

IT IS A GOOD IDEA TO TRY ALL LIGHTS AT THIS STAGE IF THE LICENCE
PLATE ILLUMINATOR FAILS YOU WILL NEED TO SWOP THE BULLET
CONNECTORS OVER.

REFIT THE PILLION SEAT.

REFIT LICENCE PLATE (IT MAY REQUIRE RE-DRILLING).