background image

10

800-621-8560

To lower temperature in the refrigerated rail:

A. Push and hold the

“set”

button until 34 appears and then release the

“set” button. 34 is the current set point temperature.

B. Push and release the up arrow 2

times

until 32 is displayed. Push and

release the

“set”

button one

time.

The new set point, 32, will flash 3

times and then will be locked in.

NOTE

:

It is recommended to only make changes of 2 degree increments

at a time. Allow for the unit to operate 24 hours between adjustments. If
the 2 degree adjustment is not enough another adjustment can be made.
The maximum highest setting is 38 degrees and the minimum lowest
setting is 28 degrees. If the settings need to go above or below this point
there may be other contributing factors as to the cause of the
temperature variances, please contact the factory at 1-800-621-8560.

The base te

m

perature

c

an also be adjusted by the te

m

perature

c

ontrol dial lo

c

ated

on the front of the refrigeration

c

oil inside the refrigerated base. The ther

m

o

m

eter

for the base te

m

perature is lo

c

ated in the

m

e

c

hani

c

al housing (Figure 1, ite

m

b).

To adjust temperature in the refrigerated base:

A.

Locate

evaporator

coil

inside

cooler

between the

mechanical

housing

and the set of refrigerated drawers.

B.

Thermostat

is

located

at top front of evaporator

coil.

There are

numbers

to indicate settings.

C.

Turn clockwise for colder setting (higher number).

D.

Turn counterclockwise for warmer setting (lower number).

NOTE: It is not recommended to turn the dial above 8 or below 1 on the
temperature control. If the adjustments still do not result in proper
temperature please contact the factory at 1-800-621-8560.

Summary of Contents for PH48SPA-L-R























Reviews:

Related manuals for PH48SPA-L-R